Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. EricOtt

    More MCK 6000 PBX Gateway Help Needed

    The exact same thing happened to me. Conclusion from MCK was that the flash memory on the board was defective. Had to replace the unit. The image was there but couldn't load into the flash memory, saw an error and kept rebooting. Don't know if it helps but i thought i could share!!
  2. EricOtt

    IAD VOIP Megaco

    I'm using the NEC BlueFire IX2010 routers at both the main and remote site. I'm also on dedicated DSL circuits 1.5 MBs
  3. EricOtt

    IAD VOIP Megaco

    Sorry for being late, I'm currently running service pack 2 (Did the upgrade from the cd's).
  4. EricOtt

    IAD VOIP Megaco

    BTW I'm using ADSL high speed at 1.5 Mb/s with 2 NEC bluefire router IX2010. There is no computers on the ADSL. It is used only for VoIP. Thought you should know!
  5. EricOtt

    IAD VOIP Megaco

    Hey Chris, 1)I've tried calling internally from a IP Phone at my remote location to another IP phone at the same location, works fine. I've tried from IP phone @ remote to DTH phone @ main location, works great too. Quality is good. 2)If i'm at the remote location, on a IP phone, and having a...
  6. EricOtt

    IAD VOIP Megaco

    Hey guys, i'm using a IAD card to do VOIP (Megaco) on Elite 192 V9.5. Everything works like a charm except for 1 thing. When i'm at the remote location and having a conversation with an outside caller, sounds like the voice/phone works like it's half-duplex. I've tried all sorts of adjustments...
  7. EricOtt

    NEC Elite 64 VM Doesnt always work

    What type of voicemail is it? If you look inside the cabinet, it should tell you on the card either FMS or VMS or VMP and if you look on the hard drive/flash card it will tell you the version of it. Usually starts with Q then 5 digits. There has been some issues with voicemail card locking up...
  8. EricOtt

    change time and date

    Changing the time and date on the Nitsuko 124i telephone system: 1) All time changes must be made from extension 301. 2) With the phone hung up press CALL 1 3) Dial 828 4) Dial the Password (Normally 0000). 5) Dial two digits for the year (e.g., 97) 6) Dial two digits for the month (01 -...
  9. EricOtt

    PC Attendant on Elite 192 trouble

    I've installed a number of those CT-U adapters and had very few trouble with them. One of them was giving me the same trouble as what you are describing and figured out that the software i was trying to interface it with was not compatible and not supported by NEC therefore i changed the...
  10. EricOtt

    NEC IPK K-CCIS

    After fiddling around with all the dipswitches and connecting deconnecting and reconnecting left right and center i got this thing going. I wrote it all down for the next time!!! I am using T1 interface. Thanks for the reply.
  11. EricOtt

    Outside not selected when press 9

    On your system, when you press 9, it will grab a free line on your system starting by the last one in the line group.i.e if you have 5 lines it will grab line 5 then 4 then 3 etc... On that specific phone that shows an error when you press 9, it seems like you don't have a line appearance on...
  12. EricOtt

    NEC IPK K-CCIS

    I have two IPK systems that i need to hook up together via K-CCIS. The 2 systems are side by side and i have all the hardware necessary but not quite sure what gets connected to where or on what. I do have the programming manual for it but without the hardware correctly connected it obviously...
  13. EricOtt

    Electra Elite 192 Line name

    Electra Elite 192 Line name is the title of his post!
  14. EricOtt

    Electra Elite 192 Line name

    To edit lines, it's mostly in system mode 3.The data no. will depend on what you want to do. To change the line name it is 00. Trunk-to Trunk group it's 03 etc...
  15. EricOtt

    Electra Elite 192 Ringing Questions

    2)Ring back tone on elite192 wont work if the version software is lower than 7.01 (To check it press feature + 3 on any phone). Unless they've changed it or there is another way,i've tried and it doesn't work.(Unless you upgrade)
  16. EricOtt

    elite48 +fms(2) +fax setup help

    If you have a coid-4 in that system you could use the fax branch extension. (Fax co line on post 4 and fax machine on post 8 of the card) Make you don't have anything programmed in 4-01 4-02 and 3-42 3-43 for co4.
  17. EricOtt

    IPK Programming Problem

    From what i can understand it looks like there is no voicemail box assigned for ext 102. If this is the case you will need to find out who is the system manager of the voicemail system. The system manager will have the option MGR in his own voicemail box. Ater pressing the softkey MGR they will...
  18. EricOtt

    Can't find adress/contacts book. Outlook

    Thanks for your great help, followed your instructions and got all my contacts back exactly where your said they where. Thanks
  19. EricOtt

    Change the Name

    To change the extension name you'll need to get into programming mode (on port 1 or 2) and look under program 4-18 (If you are using the phone to program) Otherwise in pc programming it's ALT+BTT
  20. EricOtt

    IPK ESI-B ESI-E Cards

    New2NEC : I don't need to move any of the cards as the ESI-E mounts to the ESI-B card. With the SAT software you can move cards to another slot and it will the retain the programming but in my case i need to delete ports 7-16 to get the ESI-E to be able to use those ports. I wish i could tell...

Part and Inventory Search

Back
Top