Search results for query: *

Video Connector is for a Monitor pst, even model C could be programmed with a dumb terminal through the RS232 port

After sitting on a shelf for a year all data is lost so forget about any PRI codes, you dont have them any more any how

Check the setting on the target lines where you are asked what to do in a busy condition, my memory fails me exactly what it says but there is an option for busy signal or not

Put a UPS on the KSU

Explain your number string you showed. Your digit stream should be similar to either 15551231212 or 915551231212

Go into the Line setting and set them for LONG CO this will bump the volume up a good bit. Usually helps. Otherwise you will need to set up a conference bridge of some sort. All POTS line to POTS line conf calls experience a volume drop, regardless what system you are using

The startalk Plus did have an option to use Norstar Voice Mail Manager (Sold Seperately) or you can use the KVM but to enable the KVM is a key code you have to purchase BTW there have been options available for PC programming on ALL Norstars since The 8X24 Dr3 and Start Talk C Model 2.0.0.1

The meassage you are seeing is not important. Unless the HDD is noicy or there is a long delay between messages being left and The MSG for you notification is delivered. In the event that a Hard Drive were to fail you can get an advance replacement of the NAM fully updated and refurbished usally...

Send the wheel lock back and get the Algo Duet Plus All your worries will be over Full Stop. I have inst6alled this arrangement on at least 50 customer sites with absolutely NO problem BTW it is also the ONLY AUX ringer supported by Nortel

Get the ALGO duet plus with the loud speaker option. You cant go wrong with it. It is designed for the norstar and has FULL instruction on how to set it up with very clear pictures. available from Graybar

Run a 2 inch drywall screw in the back board leaving 3/4 inch sticking out, hang cabinet like usual, just be sure to use your level and screw it in at the bottom. I have done this many many times

NEC can provide analog ports Norstar can do analog ports Connect the analog ports of one system to available CO ports on the other. A bit of fancy programming later and you are done {old school}

Please PLease Please make sure there is an over ride for 911 and TEST TEST TEST. The liability issues of not allowing 911 is more than I can bear to live with. PLEAS MAKE SURE YOU CAN MAKE THAT 911 CALL

The correct software version for the nam to operate on a MICS 7.0 is 4.1.04E You will have to get the upgrade CD and its codes from a Nortel Authorized dealer, or back up the programming and send to a refurb shop so they can upgrade AND verify that you NAM is in good working order you know test...

Star talk plus is a first issue of the NAM, it is a cross over to the beginning of the nam If you have any of the books on the old C model startalk, or remember it, you are in good shape

You would be wise to if possible put the 2 copper ports of the NAM on a core KSU port i.e. 0101 thru 0132 When the NAM was first introduced, ITAS would not assist if you were on a non core port. This also helps in the event of a station module going down, then at least the NAM still works. Re...

itphoneman I would suggest a quick reboot to start off with. Just be sure you have the PRI codes originally installed as a back up. If you are able to get things back up and running with a reboot, you should look into upgrading from 5.0 MICS software. This version had issues from day one. My...

The best non union training is OJT with an experienced old phone dude. Other wise join the union and let them teach you

A well planned and installed cabling job does not have to be hidden, nor should it be painted. In a loft office with everything exposed and painted, you would do best by installing Erico brand of CAT 32 J hooks in a straight line, incorporate 90 degree bends where needed and buying cable a...

I am glad to hear that the problem has cleared. Having just read you question I was going to suggest that you rebuild the mailbox from scratch AND reboot the entire system. Either way, glad to see problem resolved