Search results for query: *

RIP is a classful protocol. Ip 172.16.90.1 is a class B address network. Rip will only use frist 2 octs. Rip is confused with the mask 255.255.255.0 = Class C address Your 2 options are change ip to 172.16.90.1 255.255.0.0 or add: ip classless ip sub-net zero commands Then you will see...

You can only upgrade your flash. check www.ebay.com for cheap flash ram

I know this may sound like a sill question but here's my prob. I use Norton AV not Arcserv anti-virus. I create jobs with no virus scan (GFS & non-GFS) the job runs OK for 3 or 4 days then BAM!! Job fails, I take a look at the job and virus scan is enabled. I remove the check mark and job...

I feel your pain my friend. I had some of the same problems. We upgraded from 6.6 to AS7.I run Novell 6 w/SP1 (not SP2), pure IP, with AS7. Before the upgrade all was fine >>after 0 jobs were backing up. Some of the jobs you can see some you cannot. Tried to fix but to no avail. Even with the...

Links wan set to 68.22.0.161/255.255.255.224 Disable DHCP NAT is automatic Static routing <on Links> Assign ip and mask >> hop if going to another router Gatway will be 192.168.1.1 for each route you create 10.241.x.x <<this will need to be asigned on Pc's as well>> Under port forwarding Disable...

Using dialer map statements with PPP encapsulation

It can be done with the Links it just needs extra work. You need DHCP disabled, static enabled, asign IPs. Linksys FAQ > step by step...

Depending on the ver of hypterminal you have 3 choices: Win 98 Break key Ctrl-Break Ctrl-F6-Break >ver 595160 for NT workstation ^$B = Shift6+Shift4+UpperB this must be done within 60 sec of a power on this will put you in romon mode &quot;>&quot; type &quot;?&quot; for a list of commands...

Check or replace cable (rollover cable) also try booting router first I had say prob with my 2500's

Thats correct!!! Settings are. 9600 baud rate No parity 8 data bits 1 stop bit No flow control

You will need to enable multi-homing http://www.cisco.com/warp/public/cc/pd/iosw/ioft/ionetn/tech/emios_wp.htm

Sim's are ok if you dont have the money, but they will only take you part of the way. If you can buy a real ISDN sim from Teldone or others. This will set you back $1200 to $1500 but it is the best was to go. You can find them on ebay.com If you go with software version, you may want to rent...

Ok here's the sernerio. AS7 running on Novel 6 on compaq poliant servers. We recently went pure IP on this network. Also as we regularly do, we changed user acount(Admin rights)to a new account name. Now I have some job's running, yet when I go into look at the job status there are no jobs to...

Silly Q but is ipx routing on router. first enable ipx routing on router Router(config)#ipx routing [node] then interface Router(config-if)#ipx network Router(config-if)#encapsulation ppp Router(config-if)#ipx ipxwan [local-node {network-number | unnumbered} local-server-name retry-interval...

see thread478-283307

Use &quot;debug ip packet and debug dialer packet&quot; to dedermine what is bring up the line. More than likely it is a routing update. Check the good interfaces to see what you are using there (ie. Snapshop routing)

You would still get IP conflict.

I dont believe so. The 2950 cannot do that. Network devices in different VLANs cannot communicate with one another without a router to forward traffic between the VLANs

If you use point-to-point subinterfaces, you will have to assign one PVC (and thus one protocol) per point-to-point subinterface. This is the easiest and recommended way to implement routed RFC 1483. Unless you encapsulate ipx into ip and tunnenl it...

I'm not sure about your math. Where do you get 20 servers? A - 150 nodes, 10 remotes with 35 nodes each =350 B - 100 nodes, 3 remotes with 20 nodes each =60 C - 50 nodes, 3 remotes with 10 nodes each =30 Total= 440 + Ip address 16 remotes (you mean routers right) Anyway I wouldn't...