Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by tiremd

  1. tiremd

    Strange...new network shows up on my home PC?

    If you aren't currently using the wireless portion of the router, you can turn that off...at least that's the way it is on most Linksys routers....disable wireless Or, like was mentioned, change your SSID, disable the broadcast of it, and enable WEP..
  2. tiremd

    Cisco 7206VXR from an 7500 series

    Just throwing out an idea here..but I believe Cisco frame-relay encapsulation defaults to a cisco propriety type of encapsulation...to do universal multi-vendor, you'd need the 'frame-relay encapsulation ietf' command on the physical interface. Its possible that your service provider and your...
  3. tiremd

    CISCO 1751 voice-port UNRECOGNIZED!!!!??????

    Yeah, PVDM is the key.... I think that's required to do voice in that router, although with the appropriate VIC card
  4. tiremd

    Connectivity problem - is it the switches?

    If it was arp entries, they should eventually age out, or you could manually clear them on the adjoining routers/switches. So, I'm thinking its something else, although I'm not familiar with the Big-IP switch.
  5. tiremd

    ISDN Port type on 250x router

    I think all 2500 isdn ports are S/T, except for the modular SM cards that go in 2524's and 2525's.
  6. tiremd

    Cisco 3640 flash upgrade

    32M of flash in a 3640 is typically 2 16MB simms..
  7. tiremd

    Factory Reset 2600 Router

    also want to control-break during bootup and 'unset' any nondefault set variables....plus set the config-register to 0x2102.
  8. tiremd

    How to delete Partition Flash memory on Cisco 2503

    I can't remember the exact syntax, but you need to do a 'del flash' and then select partition 2, or 'del flash:2'. That will erase the second partition. Then, you need to combine the two partitions into 1 with conf t partition flash 1 If you do a 'show flash' then you should have 1 partition...
  9. tiremd

    Cheapest 100Mbps Router

    If you need speed, go with the switch (Layer 3).... if price is most important, go with the router...
  10. tiremd

    Cheapest 100Mbps Router

    You'll need at least a 2621 if you want 100Mbps ethernet... 2611 only has two 10Mbps ethernet ports. Or a 3620 with an NM-2FE2W....all end-of-life stuff so you should be able to get a good deal on it.
  11. tiremd

    Route to CCNA

    Hey CG, 1. No, I think you need the newer comp exam 640-801?? Or it can be taken as two seperate exams? 2. I think you can pass the CCNA with simulation labs, equipment would be helpful, but not necessary...if you want to continue on to CCNP then it would be a good idea to get your hands on...
  12. tiremd

    Cisco 2514 & NIU Question

    10BaseT is default on a 2514... no 100BaseT capability.
  13. tiremd

    CCIE Written

    Drae.. I'm also studying for CCIE written Routing and Switching (scheduled in December), just finished CCNP last month. I'm using the CCIE Exam Certification Guide and will most likely use Boson Exams for preparation. I work directly testing and configuring Cisco routers and switches, so...
  14. tiremd

    Dumping Config

    you must be in privileged exec mode to issue those commands... type 'enable'... might ask for a password if one's set, hopefully you know it.
  15. tiremd

    Dumping Config

    show startup-config for what's saved in nvram, and/or show running-config for what the router is currently using (in case you've made changes and they are different, probably not)...
See more

Part and Inventory Search

Back
Top