Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by jpm121

  1. jpm121

    Unable to send to AOL - outbound IP shows router IP

    Sounds like you have at least 2 static IPs, 1 for your router and 1 for your Exchange server. Assuming that the Exchange server is going out that router, it would mean that NAT on the router for outbound is not set up correctly. For whatever reason, AOL's spam filters apparently don't like the...
  2. jpm121

    Routing issue with direct connected Networks

    I guess I'm confused about your config -- your router appears to have 2 interfaces assigned to the LAN side, but none to the WAN side. Aren't you using it as a router? The way you describe your network, you need 2 subinterfaces on the router's LAN side (10.1.1.0/24 and 172.16.0/24) and then a...
  3. jpm121

    Analog phone connected to paging system not loud enough

    What kind of hardware is housing the FXS? If it's Cisco voice port you can use the 'input gain' commands to modify it.
  4. jpm121

    Voicemail password reset in call manager express

    Must be the week for it. http://tek-tips.com/viewthread.cfm?qid=1717366
  5. jpm121

    Can't Dial Local When adding the Area Code

    This varies by locale. Here in Illinois (former SBC territory) we have to use 11 digit dialing for every phone call, local/toll/LD.
  6. jpm121

    CUE

    Two options. First, easiest, is use the GUI (web browser, point it at the IP address of the CUE). From there you can do most of your move/add/change/PW reset stuff. Second option -- assuming the CUE is running in a Network Module (NM-CUE or a subsequent variant): do a "sh run" and scroll down...
  7. jpm121

    PRI Circuit Cost?

    No, it is not. Just tell your customers the truth, they'll be okay with it. A PRI, by definition, runs over a T1 type circuit from the smartjack in my building to the CO. Now, your offering may emulate a PRI circuit in terms of how my gateway router process calls and signalling, but that does...
  8. jpm121

    PRI Circuit Cost?

    The whole SIP PRI/virtual PRI thing is really annoying to me for some reason. A PRI has always meant one particular thing -- it's a telco circuit that provides 23+1 channels, has its own features and characteristics, and was a known quantity. Everyone in the biz liked PRIs because of their...
  9. jpm121

    PRI Circuit Cost?

    Not with usage, unless they're selling a virtual PRI service which is just running SIP from an Adtran or something like that.
  10. jpm121

    GUI for Cisco Call manager express and Unity Epress

    CME and CUE don't use a GUI program, they are web accessible from any browser, or even a console cable to the router.
  11. jpm121

    adding a 2 phone remote site

    Why a 3560 switch? Throw a fastethernet POE card in the 2811 and call it a day. If you insist on a standalone switch check out the 2960 - they make an 8 port POE version.
  12. jpm121

    Exchange Mailboxes on Phone

    Did you try adding it as a second account? I think that's what I had to do, but it's been a few Android versions ago.
  13. jpm121

    CISCO feedback

    The downside of the Apple phone system is every 2 years you have to forklift replace the entire thing, including handsets, and run all new cabling in your building every 3 refresh cycles. [bigsmile]
  14. jpm121

    Limit a local user to 500mb per day?

    What are things you can't do with just a Cisco ASA" [ponder] Seriously, you're going to need some external filtering to accomplish that, unless you want to rate-limit the speed of the pipe all day long to stay below the cap.
  15. jpm121

    Help! incoming mail down after isp upgrades t1 10 to 20 meg

    My guess? Your ISP either changed your WAN IP address, or mangled the routing tables when they changed you over to the faster line. It's also possible they messed up the config on the Adtran -- it's not a "copy" as you suggest, someone has to actually translate from Cisco to Adtran.
See more

Part and Inventory Search

Back
Top