Search results for query: *

Hi all I'm running a CUCM 6.1 and want to set it up to change some tones with recorded messages. Annunciators are configured and registered but i need your help for the next steps: - Installing the wav files in the CUCM - Assigning tone replacement with specific file - Other step? Thanks for...

Hi HmmG3 Isn t it possible to put the company name at the top of the screen above the Line Text?

Sorry i guess my question was not clear: On an idle display i want to show the name of MY company It is possible to have a company logo using xml file but i want an easiest solution please... Thanks a lot to advise

Hi How can i display the company name on the screen of a 7960? I run CUCM 6.0 Thanks

Hi I encounter the exact same issue than the one described in this thread: thread1361-1255985 ...but i still don't find any solution. The incoming and outgoing trunk is the same It's an analog trunk unsupervised. After coming into the auto attendant menu, then press 2 or 3 for joining an...

You're right... I'm going back to rls 2 :-(

Hello i run a cs1000E rls 4.5 I encountered a problem with all my Softphones i2050 when trying to register to the SS. A "Licensing failure" message appears before the registration is granted. It's not a CS IP users licenses because the phone is already created. Looking in the i2050...

In the Miran administration windows select A0 or A1 as the source. The external source must send an audio signal on the specific analog source 0 or 1

Hi The EES is for sure working on the QSIG. Then from the router to the IP network, the EES signaling have to be tandemed into H245 tunneling protocol. The way to prove it's working or not is to sniff the outgoing port on the router using Ethereal or any other sniffer and search for H245 data...

Try with IE rls 6 A patch in the deplist also solve that issue

Adding an IP ATA might be the solution. But after many tests i can say that you will experience many problems. Depending the originating and destination fax machine brand that connection will not work. Canon faxes are really incompatible... The other solution is to install a Media Gateway in...

On another Mail rls 12 system

Depending the SW rls, you can eighter load a "loadware" file from the pdt or load a new psdl file that required a sysload. These files are accessible from the Nortel Web site

Isn't the Break In (BKI) Key of M2250 gives the ability to freed the trunk?

I already try the same configuration but it doesn't apply while the paddle board is inserted. The way to save DNUMs is to use External MSDL instead of Daughterboard MSDL

Here is a printout of new user creation with Rls 4.5: ld 17 CFN000 MEM AVAIL: (U/P): 45379934 USED U P: 5972950 260808 TOT: 51613692 DISK SPACE NEEDED: 338 KBYTES DCH AVAIL: 253 USED: 1 TOT: 254 AML AVAIL: 14 USED: 2 TOT...

LD 17 CHG PWD PWD2 required LAPW OVLY LOGIN_NAME xxxxx PWD yyyyy OVLY all or overlay numbers

You have to change the CFWT prompt in LD 56 FTC table, then init the PBX to make the changes active

Service Domain is defined only in the NRS. If more than one NRS, yes it have to be the same. The SIP Gateway Endpoint name is the one defined in the SigServ Node configuration. Each SigServ have its own name.

In the NRS: - define Alternate NRS IP@ - Log into the Alt NRS, and define the Primary NRS IP@ In Primary NRS define: - a System Domain - a L1 Domain - a L0 Domain - Create a Gateway Endpoint for all systems: Main office, Remotes offices using either h323 or SIP protocol. Don't forget that your...