Touchtone\Keypad tone across QSIG link via Cisco

[scottvtr]

I hope someone can help with a problem I have with a site in Madrid.
They have a CS1000S running release 5, One sig server etc.... There's a PRI connection (QSIG) to an E1 connection on a Cisco router which provides on-net VoIP to the rest of our company globally. The voice works fine but when users on-site try to dial up a conference bridge hosted on a different site they are unable in input their 4 digit passcodes (not accepted).
This sounds like the conf bridge is not recognising the buttons pressed, which makes me think the keypad tones are not working across that link. If the users dial the full DDI number of the conf bridge, routing across the public network then it works.
It appears that the fault only occurs on the OSIG route. The local vendor have washed their hands of the problem, stating it must be a config issue on teh Cisco router but we have other sites using the same router config without a problem???

Here are copies of the routes, route 1 is the good one.

ROUT 1
DES PRIMARIO
TKTP DID
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI2
ISDN YES
MODE PRA
IFC EURO
CNTY ESP
SBN NO
PNI 00001
NCNA NO
NCRD NO
ISAR NO
CPFXS NO
HNTN 916
HLCL 267
SDID NO
DAPC NO
INTC NO
DSEL VOD
PTYP DCO
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 90001
TCPP NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 1
NDNO 1 *
DEXT NO
DNAM NO
MFC NO
ICIS YES
OGIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GTO 896
GTI 896
SFB 3
NBS 2048
NBL 4096
IENB 5
VSS 0
VGD 6
DTD NO
SCDT NO
2 DT NO
DDO NO
DRNG YES
NDRI 00
CDR NO
NATL YES
SSL
CFWR NO
IDOP NO
VRAT NO
MUS YES
MRT 40
MR NO
PANS YES
EQAR NO
FRL 0 0
FRL 1 1
FRL 2 2
FRL 3 3
FRL 4 4
FRL 5 5
FRL 6 6
FRL 7 7
OHQ NO
OHQT 00
TTBL 0
ATAN NO
PLEV 2
OPR NO
PRDL NO
EOS NO
DNSZ 0
RCAL NO
MCTS NO
ALRM NO
BTT 30
ACKW NO
ART 0
PECL NO
DCTI 0
TIDY 90001 1
SGRP 0
ARDN NO
AACR NO


BAD ROUTE

ROUT 2
DES VOIP
TKTP TIE
NPID_TBL_NUM 0
ESN NO
RPA NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI2
ISDN YES
MODE PRA
IFC ESGF
SBN NO
PNI 00001
NCNA NO
NCRD NO
CTYP UKWN
INAC NO
ISAR NO
CPFXS NO
HNTN
HLCL 6907
DAPC NO
INTC NO
DSEL VOD
PTYP DTT
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 900002
TCPP NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 2
NDNO 2 *
DEXT NO
DNAM NO
SIGO STD
MFC NO
ICIS YES
OGIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GTO 896
GTI 896
SFB 3
NBS 2048
NBL 4096
IENB 5
TFD 0
VSS 0
VGD 6
DTD NO
SCDT NO
2 DT NO
DRNG YES
NDRI 00
CDR YES
INC YES
LAST YES
QREC NO
OAL YES
AIA NO
OAN YES
OPD NO
NDP EXC 0
CDRX NO
NATL YES
SSL
CFWR NO
IDOP NO
VRAT NO
MUS YES
MRT 40
PANS YES
FRL 0 0
FRL 1 1
FRL 2 2
FRL 3 3
FRL 4 4
FRL 5 5
FRL 6 6
FRL 7 7
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TTBL 0
ATAN NO
PLEV 2
OPR NO
ALRM NO
ART 0
PECL NO
DCTI 0
TIDY 132 2
SGRP 0
ARDN NO
AACR NO

 

[phones1]

couple of questions.
1. Is the model of router the same at other sites
2. Is the IOS the same as on working sites
3. PRT the config of the QSIG link (router side)
4. Did you build your Trk members in reverse on the CS1k side as Cisco recomended this?

As i have found with most Nortel to Cisco problems Cisco are normally to blame as they always try to put thier own version out of an industry standard which means it doesnt quite work 100%

Remember if it doesn't work hit it harder

Scott UK

 

[scottvtr]

Hi,

Thanks for responding.
The router models and IOS are the same as our site in Portugal which works, however the difference is that theis is the only site with a CS1000S running release 5.

Our vendor built the system so I can't be 100% sure they configured the members in reverse.

Here's the relevant parts of the router config:

trunk group 1
max-calls voice 30
hunt-scheme sequential both up
!
voice-card 0
no dspfarm
!
voice-card 1
dspfarm

controller E1 0/0/0
framing NO-CRC4
pri-group timeslots 1-31

interface Serial0/0/0:15
description Andromeda(cres01_s2_0-voice)
no ip address
encapsulation hdlc
no logging event link-status
no snmp trap link-status
isdn switch-type primary-qsig
isdn incoming-voice voice
trunk-group 1
no cdp enable

dial-peer voice 1 pots
trunkgroup 1
voice cut-through alert
description *** Madrid PABX Extension ***
destination-pattern 690....
progress_ind alert enable 8
incoming called-number .T
fax rate disable
direct-inward-dial
forward-digits all
!
dial-peer voice 10 voip
voice cut-through alert
destination-pattern .......
modem passthrough nse codec g711ulaw
session target ras
incoming called-number .T
dtmf-relay h245-alphanumeric
fax rate disable
fax protocol pass-through g711ulaw
ip qos dscp ef signaling
no vad

Cheers.

 

[phones1]

Log onto the CS1k

ld 21
REQ: ltm
route:2 (in your example)

also please prt a trk TN from a known working switch & your Rls 5

Remember if it doesn't work hit it harder

Scott UK

 

[acewarlock]

Is EES turned on in the CDB? if not when the trunk timer ends so does EES unless you using a 500 type set. try it it with a 500 set to see if it works and if it does than it's your CDB setting.




This is a Signature and not part of the answer, it appears on every reply.

This is an Analogy so don't take it personally as some have.

Why change the engine if all you need is to change the spark plugs.

 

[scottvtr]

Hi,

I've got EEST set to YES (and DTMF to YES as well) but EESD is set to NO.

Here is the LTM and a Trunk TN:

ROUT 2
TYPE TLST
TKTP TIE
ROUT 2
DES VOIP
TN 021 01 MBER 1 KNET
TN 021 02 MBER 2 KNET
TN 021 03 MBER 3 KNET
TN 021 04 MBER 4 KNET
TN 021 05 MBER 5 KNET
TN 021 06 MBER 6 KNET
TN 021 07 MBER 7 KNET
TN 021 08 MBER 8 KNET
TN 021 09 MBER 9 KNET
TN 021 10 MBER 10 KNET
TN 021 11 MBER 11 KNET
TN 021 12 MBER 12 KNET
TN 021 13 MBER 13 KNET
TN 021 14 MBER 14 KNET
TN 021 15 MBER 15 KNET
TN 021 16 MBER 16 KNET
TN 021 17 MBER 17 KNET
TN 021 18 MBER 18 KNET
TN 021 19 MBER 19 KNET
TN 021 20 MBER 20 KNET
TN 021 21 MBER 21 KNET
TN 021 22 MBER 22 KNET
TN 021 23 MBER 23 KNET
TN 021 24 MBER 24 KNET
TN 021 25 MBER 25 KNET
TN 021 26 MBER 26 KNET
TN 021 27 MBER 27 KNET
TN 021 28 MBER 28 KNET
TN 021 29 MBER 29 KNET
TN 021 30 MBER 30 KNET


DES KNET
TN 021 01 VIRTUAL
TYPE TIE
CDEN SD
CUST 0
TRK PRI2
PDCA 1
PCML A
NCOS 0
RTMB 2 1
B-CHANNEL SIGNALING
TGAR 1
AST NO
IAPG 0
CLS UNR DTN CND ECD WTA LPR APN THFD XREP BARD SPCD
P10 VNL
TKID
AACR NO

 

[dlesap]

Hi

The EES is for sure working on the QSIG. Then from the router to the IP network, the EES signaling have to be tandemed into H245 tunneling protocol.

The way to prove it's working or not is to sniff the outgoing port on the router using Ethereal or any other sniffer and search for H245 data block.

The issue is not in your CS1K

 

[johnpoole]

stare and compare the cdb in the working and non working nortels... your ees setting may not match,,, then wash your hands of that vendor.. a decent vendor will not leave you in that shape even if it;s your problem they should be able to tell you where it's broke...

john poole
bellsouth business
columbia,sc