Search results for query: *

Hi Steve, I've issued your command dadmin@S8720A> stty echo dadmin@S8720A> however, still not able to echo what was typed. I've read thru the MAN page for stty but doesn't seems to have anything else relevant.

Dear all, I was not able to echo what was type within the shell, is this something that can be fixed ?

Dear all, The switch and VAL board allows successful recording, but it will playback nothing. Seconds shows correctly in "list integrated xxxx". Existing announcements plays fine. -------------------------------------------------------- VAL-ANNOUNCEMENT TN2501AP HW13 FW016 Time...

Dear all, Agents will be AUXOUT after 3 rings if they don't answer an ACD call...where do i change this time or number of rings? Thank you very much

have you define your node-names?

if you do a list trace on the trunk and in there it shows no name that means your carrier isn't sending you any ANI or the caller is calling from a number which doesn't have outbound caller id which is also programmed at the telco's end....usually if there's ANI info it will pass thru your VDN...

could be a firmware issue on either the MM711 module or the S8300....i would submit a ticket to your BP or avaya to have a look at it

create another coverage path using 'add coverage n' should be your next one....ie 107, program it just like coverage path 106 and see if 107 works after 6 rings....if it does do a remove coverage 106 and just use 107. could be a corrupted entry in the coverage table i had that once....

did you create an ip-service and bind SAT on one of the CLAN's?

Dear all, What is the current status for Integrated Management on Windows Vista? Does it work on Vista with the current Integrated Management 4? thanks

on the trunk form i think either page 2 or 3, try putting a 'n' to suppressing # and monitor it for a while....

excellent CBB...i will give that a try....

Dear all, I'm trying to install the VAL management tool (3.0.16) but it will not begin the installation with this error message: "An unsupported version is detected, please install this current version or upgrade the current version" and exit the installer. I have ASA installed on my notebook...

bidon123 main and lsp restarts? or main restart for no reason causing lsp to restart? what CM version on both? run 'disp init' do you see the restart cause? any alarm or error?

Dear all, recall my last post on going for the 4th time: 1st attempt: 821 / 849 2nd attempt: 770 / 849 3rd attempt: 834 / 849 4th attempt (today): 910 / 849 I FEEL GOOD.....DA DA DA DA DUM..... =)

CiscoKidUK, good try...check my 'going for the 4th time' post....i'm going for my FORTH time tomorrow...that's right the 4th time....i'm sure you'll find yourself in a lot better situation than i am right now....good luck on your second shot

Dear all, 1st attempt: 821 / 849 2nd attempt: 770 / 849 3rd attempt (today): 834 / 849 apparently not good enough to the Cisco standard....i'm not gonna give up....whatever it takes man if it needs me to do it 15 times i'll do it..... S.O.B.......

no problem mentallimit

don't worry about harming service for now tbenton12, port network 1's connectivity to port network 2, 3, 4 & 5 is entirely ceased. You need to fix this quick. Try to: 1- reset board 1d03 and do it 1 at a time to see if it fixes itself 2- list fibre and look at the counterpart where the other...

here's why: 3:31:03 denial event 1751: No AAR/ARS route pat/pref D1=0x8b0a D2=0xc1c0019 13:31:03 call-forwarding 91586XXX resolution: 1- change ars ana 1 2- string is 1586 min = 4 max = # of your cell phone digits 3- goes out route pattern 1