Search results for query: *

ITG TRUNK GROUP GETTING PRI0202 CODES. WHAT DOES THIS MEAN

it appears the port is locked up you get no response from pdt and cannot go back to the switch side. the only way i have found to release it is to ini the switch on site. and yes i am still on the modem. when if i hang up and dial back in no response form the switch or pdt

I have dialed into the system sent the files over modem line and do not understand the term shell. How can I open a new shell when the modem port will not respond to pdt or the switch side. cannot communicate over modem line. how do I open a new shell

using pdt to send patch zip file to A: ssc or u patch directory before it completed locks out port you are sending over and cannot talk to switch or pdt

TRY NDS UNDER RCAP FOR THE D CHANNEL. I THINK YOU WILL HAVE TO DIABLE THE D CHANNEL TO MAKE THIS CHANGE THEN ENABLE IT AGAIN.

there is no disconnect options for routes using isdn pri

and sucession 3.0 or above software

This can only be done if you know the pwd2 or master password

4 mega bit disk were used up to release 23. the only place we were able to acquire them was from notel

YOUR DLOP SHOULD BE PRI 06 23 FRAMING ESF LCMT B8S YALM FDL CHANNEL 24 IS WHERE THE D CHANNEL IS BUILT UNDER ADAN.

the strapping pins at j12 on the ssc card needs to be in place for the ethernet to work.

IF THESE TRUNKS ARE DID YOU NEED A NUMBER IN THE LDNO OF THE CUSTOMER DATA BLOCK. IF YOU ARE A THREE DIGIT PLAN YOU NEED A THREE DIGIT NUMBER IF A FOUR DIGIT PLAN FOUR DIGITS NUMBER AND SO ON. THIS IS MY THE FIRST THOUGHT NOT KNOWING MORE ABOUT YOUR CONFIGURATION. HOPETHIS HELPS

I ASSUME YOUR TRUNK CARD IS CROSSCONNECTED TO YOUR DIAL LOGIC CARD. GET ON THE T AND R OF THE TRUNK WHERE IT IS CONNECTED AND MONITOR A CONNECTION WITH A TEST SET TO SEE IF YOU HEAR BOTH SIDES OF THE CONVERSATION. IF SO THE PROBLEMS POINTS BACK TO THE TRUNK OR OPTION 11. IF NOT PROBABLY THE...

In LD 15 under net data depending on what features and release you have you will need an enty under HNPA for your area code and an entry under HNXX for you office code this should give you 10 digit calling line ID For a long distance call dialed with ten digits. If you only dial seven digits...

The route data block is a different route than the trunk you printed. This RDB tells us nothing about your trunk. The trunk you printed out is in route 87 member 1. The route you printed is route 89. DOES THE OUTSIDE PARTY STAY ON LONG ENOUGH TO EVER GET CUT THROUGH. WAS THINKING POSSIBLE...

YOUR TRUNKS SHOULD NOT BE LOOP START THEY SHOULD BE GROUND START. YOU DO NOT HAVE ANSWER SUPERVISON MARKED YES ON THE TRUNK. I DON'T KNOW IF THE TRUNKS ARE TWO WAY BUT THEY ARE MARKED IN THE ROUTE DATA BLOCK AS SO. TWO WAY TRUNKS SHOULD NOT BE LOOP START. EVEN AFTER THESE CHANGES I AM NOT...

LD 16 ROUTE DATA BLOCK REQ CHG TYPE RDB DMOD RETURN ROUTE ENTER THE CORRECT ROUTE # RETURN DOWN TO CNTL ENTER YES ENTER DOWN TO NEDC ENTER EHT FEDC ENTER ETH ENTER ON TO END IT SHOULD UPDATE MAKE SURE YOU ARE CHANGING THE CORRECT ROUTE

ONE ISSUE THAT HAS NOT BEEN SUGGESTED IS THE TRUNKS IN THE ROUTES INVOLVED SET FOR SUPERVISON YES IN LD 14. I STILL STAND BY MY ORIGINAL STATEMENT THAT IF THE CENTRAL OFFICE DOES NOT GIVE ANSWER SUPERVISION EVEN IF THE TRANSFER IS COMPLETED THE TRUNKS WILL NOT RELEASE WHEN DISCONNECTED. ALSO IN...

IF THESE ARE ACD SETS AND THEY HAVE A DIRECTORY NUMBER ON ANOTHER KEY AND THAT NUMBER ALSO APPEARS ON ANOTHER SET. IT WILL NOT KNOW WHICH SET TO LITE THE LAMP ON. IT WILL NEED TO BE REMOVED FROM ALL OTHER SETS EXCEPT THE ACD SET TO WORK PROPERLY.

MOST DIGITAL CENTRAL OFFICES DO NOT GIVE ANSWER SUPERVISION BACK TO THE PABX ANALOG TRUNK PORT. OLD STEP CENTRAL OFFICES GAVE REVERSE BATTERY SUPERVISION ON ANSWER WHICH WOULD GIVE THE ANALOG TRUNK ANSWER SUPERVISION. NEEDING ANSWER SUPERVISION FOR TRUNK TO TRUNK TRANSFER YOU NEED A DIGITAL T1...