Search results for query: *

When calling Cell to Cell you need to call from the Cell to the DID for off-pbx-telephone feature-name-extensions "Idle Appearance Select" CM then ties the incoming CLI/ANI of the Cell to the Station and then the call will break out to the PSTN via the PBX thus allowing the call to be recorded.

Hi I completed an SIP install for MM 5.0 using S8730 Hardware for both the MAS and MSS; I installed the Perm licensed for the MAS to ensure the SIP Switch integration was activated. After completing the install the client wanted to change the DNS names for the MAS and MAS, I wasn’t 100%...

we have numerous sites in Germany all DS1 trunks are configure for enbloc, is it the case they have delivered the service as enbloc? PBX

Hi Its possible to bulk add the subscriber extensions names COS etc with ASA, but if you want to retain the personal greetings etc.. then pass.. PBX

3.4. Configuring Avaya Communication Manager For Out-Of-Band DTMF Relay via H245 Cisco GWs only support out-of-band DTMF via an H.245 message. Avaya Communication Manager supports DTMF relay via H245-signal and H245-alphanumeric from Cisco. The Avaya S8500 Media Server must be configured to send...

Tricky I dont know much about COR info being carried through DCS, but you may be able to do this in two ways: The easyest is: Site A where the VDN 6764 is Site B where the agents are Add a new VDN into site A pointing to the same vector as VDN 6764, lets call the number VDN 1234 Add VDN...

Hi I agree with BuckWeet usally a IP transport issue. PBX

Hi Yes you can change the length of time the PBX waits to collect the digits before moving onto the next step in the the vector by altering the "Prompting Timeout" in" system-parameters features" under Vectoring.. VECTORING Converse First Data Delay: 0 Second...

Hi If you ae using Windows Center Vu Supervisor, try by passing this and telnetin to the CMS and trying o log in, if you log in Ok you know the Windows install is stuffed, if you cant login then log into CMS and check there is a user setup with that login. PBX

Hi Here is the details on the card I think you have, also the pin out can be found here: http://support.avaya.com/elmodocs2/definity/def_r10_new/easy_3/OutputInstallMCC/ConnCableDiags26.htm#52200 Hope this helps PBX DEFINITY Enterprise Communications Server System Description 555-233-200...

Not sure if you are after this, there is a limit on the maxium number of sockets on a CLAN but cant find it right now, soz PBX Capacity Constraints and Feature Limitations The TN2302 Media Processor board provides up to 64 audio channels. They may be either: n channels of hairpin IP-IP. Each...

Thanks for the input, do you know if there are any Hardware limitations, the Current Processor Hardware is a revision 10, however the B carrier is from a V5 hardware statck? PBX

Hi All I need to install a new Definity G3siV10 B carrier onto a Processor carrier A carrier it is not a duplicated processor. So far I have found that I need to do the following: (i) Set Port Cabinet B (J58890H) on top of Control Cabinet A. (ii) Remove the Time Division...

Hi What does digit treament say on page 1 ? PBX

Hi If you use CDR then check out these logs, might give you some more info. Good luck PBX

Hi It does sound like you are experiencing packet loss on this H.323 trunk, I think depending on the S/W revision is you status the station that is connected across this link on the 3rd page or so, it shows the packet loss? It needs to be under 20ms according to the Avaya white paper I...

Hi Yes the feature Internet Messaging is available for "Intuity Audix" see URL: http://support.avaya.com/cgi-bin/gx.cgi/AppLogic+PdfPrint?pdfdoc=ia4plad1.pdf or http://support.avaya.com/cgi-bin/gx.cgi/AppLogic+Elmo#ELMO to search for you particular Intuity administration...

Hi You could try this, not sure if it is what you are after: If you have Coverage Time-of-day (add cov tim 1) then you can assign your main/attendant number as an exported station with cover path set to t1 etc. In Add Cover Time 1 setup the times you want calls to go to another cover...

Hi ktripp When you get it up and running again copy and rename the file persist.dat in directory: C:\programfiles\lucent\dsa\user\persist.dat This contains all the switches and login details, make a copy of it and rename persist_copy.dat etc. then if the persist.dat file becomes...

Hi I might be wrong but I don't think you can goto cover twice! e.g. Hunt 4357->Cover to 4200->Cover to ? Why? Well say I wanted my callers to my extension to cover to station 4350 after 2 rings and then after another 2 rings goto my voice mail, if the above Cover->Cover option was...