Search results for query: *

CM 7 9611g phone I have a user that experiences a couple second loss of audio when a bridged line rings and she is already on a call. The audible message waiting is set for no on her phone and the main line. It typically happens when on her headset (Plantronics) but has also happened when she...

You can try logging in command line to CPDC and entering appstart pd status (checks current status) appstart pd restart ** Proofread carefully to see if you any words out.

To check RCAP you will need to go to LD 22 Prt Adan DCH X RCAP will be about 2/3 of the way down in the printout To determine which DCH, you may want to print out your RDB in LD21 ** Proofread carefully to see if you any words out.

RIP Gene ** Proofread carefully to see if you any words out.

Avaya has a document which shows it is supported with callpilot 5.1 SU02 and above. ** Proofread carefully to see if you any words out.

I use simple green on a paper towel to clean phones. It doesn't leave a residue and is cheaper than the phone wipes ** Proofread carefully to see if you any words out.

I had an old 2 cabinet opt 11 upgraded to CS1K. I started getting static only in the second cabinet. I tried replacing everything, including the cabinet, still static. One of my coworkers suggested doing a continuous ping using a laptop to the network switch ping xxx.xxx.xxx.xxx -t Right...

Don't for get your column air filters, they should cleaned or replaced ** Proofread carefully to see if you any words out.

If your software is current, you can use the DCT command in LD 96. ** Proofread carefully to see if you any words out.

If it just stopped working, you may need to do "appstart pd restart" from command line on the SS ** Proofread carefully to see if you any words out.

oops! getting old ** Proofread carefully to see if you any words out.

@Jven I have 14 sites all on 7.5 or 7.6 with CPPM and CPDC cards, all using the PCMCIA cards. The reason I responded to this thread was I just had a card go bad. Cheers! ** Proofread carefully to see if you any words out.

Did you try EDD Clear? Also did you try a different PCMCIA card? As Perry asked, where is the backup failing? ** Proofread carefully to see if you any words out.

If you do not want the sets disabling at midnight routine, remove LD 30 from midnight routine. OR you can change FLXD to FLXA in class of service, I believe that does it as well ** Proofread carefully to see if you any words out.

Here is the link: http://www.ghtrout.com/files/Restore_Guide_Opt11c.zip ** Proofread carefully to see if you any words out.

Just type the command "reboot" and it will ask you if you are sure (Y/N) and enter Y You can do the SigServers one at a time, moving the phones to the SigServer you are not rebooting with the command disiTPS (This does a courtesy force over) disTPS (No courtesy) If you type "help" you can...

They can be kind of funky. I had a site where the PD worked on phones registered to SS1, but not on SS2. I finally moved the phones over to SS1 and rebooted SS2 to get it working again ** Proofread carefully to see if you any words out.

PD is personal directory Try checking SigServer 1 ( I noticed that is SigServer 2) It only has to work on one SigServer ** Proofread carefully to see if you any words out.

Login to the signaling via command line: appstart pd status (checks current status) appstart pd restart This will not interrupt service ** Proofread carefully to see if you any words out.

If the CPPM card is down, then you may have one of the cards with bad memory. ** Proofread carefully to see if you any words out.