Search results for query: *

This may or may not help. Had a similiar issue on Rel 5.5 with 3904's sets and t1 ld service. The LD carrier was voip with a serial T1 handoff to the switch. After a call was placed the 3904 transfer would not display when needed. It was due to the voip carrier signal for their T1 not sending...

The 202i is an IPE device which must be inserted into the switch to receive power from and communicate with the switch. DS30 connectivity with the switch is over the switch backplane so no MGate cards or DS30 cables are required. The 202i server is installed in two consecutive peripheral...

You cant use slot 10 .The 201i and 202i require 2 slots on the cabinet to work. You must use 9 or lower. If you look at back edge of the 201/202i card there are 2 card edges on it. The Opt 11 cabinet was marked origionally for Meridian Mail so there is no backplane after slot 10 to plug into...

This is a very trimmed down version of Telephony manager. Be careful using it. When you submit a change request it may or may not work but tell you its completed. I did a swap on 2 sets and a problem developed. It advised the swap could not be completed and the phones were gone. There appears to...

Also check your elan connections. If you are receiving broadcast messages over the elan it will ini your system once the buffer overflows. This is pretty common when someone moves around patch cords not understanding the setup.

Make sure your using the latest app builder version for your CP release if there's been any updates to your Call Pilot. Earlier versions of app builder will cause you headaches if you've pushed recent SU's.

No they were new. No smoke but sounds and smell. This was a chasis ug from the 68060E cpus. The AC CEPS were replaced to comply with the pwr req's. They are correct also. We checked the module pwr connector thought maybe the Mpdu's were wired factory internal wrong. But they appear to be wired...

Has anyone experienced backplane failure on this core/net module. Myself and another tech had catastrophic failure on a AC 61C upgrade. It appeared to have a short in the new NT4N41 Ccpi bay even with no cards plugged in sparking between the 2 stacked PCB's where the group plugs are. I know the...

We have several ISP1100 Sig servers. Our network is changing to a 10. infrastructure for both the elan and clan. Re-IP thru element manager is not the best solution on something like this. Other than using a boot CD on every site to re-IP the sig.srv has anyone done this thru CLAN telnet command...

Not sure on rel 5 but 4.5 after you provision esa in Ld 24 then you assign different clids for each site. Each clid has an entry ESA_HLCL you place the complete 10 digit on-site fax number there and tick ESA_INHN no and ESA_APDN no. When the user dials 911 it uses this entry replacing the usual...

This was not a Cisco solution in our case. But a vendor supplied server that had these options.

Had a similiar problem. voip LD T1 tie was not sending ACK. on connect causing 3904's starting a conference call not to display the connect screen to link up conference calls. Nortel was very clear they run industry standard protocol for t1 handshaking and if they dont get that signal "you" got...

I just had a thought. I wonder if NRS is doing something to the stream. I have the default route set to the host but it may need something more.

Hey John appreciate it. Yea this is a strange one. The rlb's are all set to ext and the pni's all match. The rcaps are set to nd2 and tat. trmb is set to yes on assoc routes. The Dchannel FE software levels are correct. I sys'd the switch last weekend. Im about ready to open a ticket with tas...

This may help also. See the below print out. Make sure your trunk members have supn set to yes and your route has NEDC set to ETH and FEDC set to ORG or ETH. Havent had any troubles on this config. Make sure the CO is sending supervised disconnect. Thats missed quite often. If you have Mer Mail...

Trying to figure this one out. Voip h323 trunking NRS. When ever a LD call is placed from the remote site it tandems thru another switch for the LD and generates the above error. The call appears to not be affected and does completed. I know its a d-channel complaint but the rcaps are matched...

You know what I just had a thought. Could it be for multi cutomer HLOC deployment ?

Intresting. When I tested a local site call last week and included the ESN your correct it strips HLOC and keeps the call internal and displays 4 digits. However with it in Ld 15 it did not work until I added the ld 90 HLOC table with the dmi so the system knew what to do. Ill be glad to strip...

Boy I missed that one sorry but you have a i2001 you can only add 1 line to it and thats it.

sch0361 is a key out of range indication. Not a feature rejection. Have you tried adding something else to key 1. Try adding this feature on a digital set or another IP phone. It looks as if your correct on your entry but the switch does not like it. Here is one of my switches, no problems what...