analog line supervision

[badro25dz]

XUT trunk don't release calls when outsider caller hungup the first. i guess that is related to supervised line.

 

[acewarlock]

You need to use GRD start trunks not LOOP start trunks.




This is a Signature and not part of the answer, it appears on every reply.

This is an Analogy so don't take it personally as some have.

Why change the engine if all you need is to change the spark plugs.

 

[badro25dz]

Hi, thanks

but my teleco don't provide a grd start loop ! how can i get grd line ??

 

[phonz1]

you have to call telco and request them and make sure to change your programming then also

 

[SuperKingCobra]

This may help also. See the below print out. Make sure your trunk members have supn set to yes and your route has NEDC set to ETH and FEDC set to ORG or ETH. Havent had any troubles on this config. Make sure the CO is sending supervised disconnect. Thats missed quite often. If you have Mer Mail forget COT it will not work. GRD or T1 is the only way.



DES LOCAL
TN 010 0 00 00
TYPE COT
CDEN 8D
CUST 0
XTRK XUT
TIMP 600
BIMP 3COM
TRK ANLG
NCOS 0
RTMB 0 1
ATDN 2400
SIGL LOP
SUPN YES
STYP PIP
AST NO
IAPG 0
CLS UNR DTN WTA LPR APN THF
P10 NTC
TKID
AACR NO
DATE 23 APR 2007


TYPE: rdb
CUST 0
ROUT 0

TYPE RDB
CUST 00
DMOD
ROUT 0
DES LOCAL
TKTP COT
NPID_TBL_NUM 0
PRIV NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK NO
ISDN NO
PTYP ACO
AUTO YES
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 8000
CPP NO
TARG 01
CLEN 1
BILN NO
OABS
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
OOD 1
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
CRD 512

IENB 5
TFD 0
LEXT 100
VGD 6
SST 3 0
NEDC ETH
FEDC ORG
CPDC NO
SPCT IMM
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
RVSD 08 31
ILLR 02 02
DRNG NO
CDR NO
MUS NO
MR NO
MANO NO
EQAR NO
FRL 0 0
FRL 1 0


PAGE 002

FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TTBL 0
ATAN NO
OHTD NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
AACR NO

 

[acewarlock]

What country are you in?

"but my teleco don't provide a grd start loop ! how can i get grd line ??"

Not "grd start loop", GROUND START







This is a Signature and not part of the answer, it appears on every reply.

This is an Analogy so don't take it personally as some have.

Why change the engine if all you need is to change the spark plugs.

 

[worldwidedialtone]

If your CO provides Loop Start trunks then look at BTID settings for one of your trunks that does disconnect. Once a trunk has a truk built on it and a BTD has been set then all the other trunks on that card get the same BTID. If this is new card/trunk install you will have to test different settings until the call breaks down from the far end "hanging up".

MIKE