jagoan - I have tenant partitioning enabled. I just need to get music from a single source to an analog port... I'm not great with electronics - can you tell me what I'd need for caps and resistors?
(blue wire)mp3 player-->6uf 50v-->8uf 50v-->analog port?
(white/blue wire) mp3 player-->analog...
Guys,
This might be bad - but I just tried connecting the following 3.5mm headphone plug/RCA cable to a cat5 cable and plugged it into an analog port, assigned a test extension to tenant 3 / music source 3 and it worked... I was able to hear music on my test extension from my computer. I...
(If I should start a new thread, I apologize in advance on this)
what are the actual wire connections with this MOH config w/a Universal Coupler? Here's what I've got:
Universal Coupler 909B
(settings below per the manual)
J1: (this is the music supply out to the Switch?) jumpers 1+2 both open...
fbs003 - thanks for that post. I had an aut-msg-wt indicator setup on cm2.2, Intuity Audix 5.1 this way:
2800 is a vdn setup as a main line to dump calls into a vector for distribution using a hunt group. I setup a day mailbox if no agents are available and used subscriber x2800. I tried...
Hey all,
Running S8500 CM2.2 at the main site on the east coast w/ single new S8300/g350 LSP on the west coast both sharing Audix 5.1 at the main site. The problem is the west coast subscribers have eastern time zone stamps on all messages. I have seen multiple posts regarding this issue...
I want everyone to be able to dial international except 4 specific extensions - which is why I was trying to limit calling ability for those specific extensions by disallowed lists/ars entries.
Merlin - everything you suggested worked like a charm with one exception. Dialing international numbers using the pool dialout code of 5 allows the call to go through - which is what I don't want to have happen.
5,9011 int calls go out.
9,011 int calls do not go out.
All of the other...
Gotcha Merlin. That makes sense. So obviously Legend calling priviledges are based on the following combination: Disallow lists, Allow lists, Call Restrictions, ARS tables... (did I miss anything?)
Is there a particular processing order that these are applied in for an outbound call (as in...
Hey all - I am trying to restrict 4 specific extensions so they are only able to dial the following: 4 digit extensions, local, toll free and 911 calls.
Here is my setup: Merlin Legend v5r10 (I think) at the remote site. Local calls go out local copper trunks. We also have a TIE T1 connecting...
I figured it out! I feel like an idiot for not catching this, but whatever. I'm glad it's fixed. If you look at Vector 1, you'll see step 5 says to queue to skill 20 if GREATER THAN 1 agent is logged into that skill. The front desk attendant is the only agent logging into skill 20, thus it...
Hey all - I've got G3si r11 w/ Audix. When you zero out of audix using 'enhanced_cover_0' to x5812 it transfers to vdn 5812 (below) which references vector 1 (below). Skill 20 (below) is the front desk hunt group and only one agent logs into that skill using the front desk agent ID (3802 -...
Hey all,
The receptionist desk moved and I needed to move the MLX-20L with DSS adjunct with it. I simply pulled the 2 pair cross connect wires from wall port A and re-punched them down to wall port B in the same positions. Now, at the new location the MLX-20 works fine by itself, however...
Hey all - I've got a Definity G3si R11 onsite. We have a local offsite office with centrex service through the same LEC that offers us our PRI at the Definity site. I'm trying to get 4 digit dialing between the two sites using the LEC's network.
Local PRI: Trunk Group 5
Remote 'extensions'...
Hey Franke or anyone else,
Would you be able to help me with this portion of my question? I'm still unsure of this part and was wondering if you could confirm from my post above?
"I am assuming I can install the new cards in slots 9 + 10 without having to move the T1 tie card over to slot...
Hey all,
I know this thread is somewhat old, but I am hoping someone might see this post. I have reached capacity on my Legend and have a spare 408 GS/LS - MLX digital card and a spare 008 Analog card that I'd like to install two weekends from now. I've learned the system on my own with no...
hhmm... check to make sure they can resolve your mx record correctly? are the error messages they're getting from their own exchange server? ...if not, it seems like they're trying to relay mail to you via a non-relay exchange server...
Hey bhawani123 - not sure if this is still an issue for you but...
We use Outlook/exchange5.5 to manage our application submissions for HR. Our Web guys setup links from the jobs page that autopopulate the subject field w/corresponding job codes. Then we setup outlook routing rules, so a...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.