Search results for query: *

The modem is in a dedicated usb port. I have 4 usb ports available and have tried it in each one, with the same problem

I Have a dell optiplex GX150 running WIN2000 Pro SP2 and as its a SFF model I have had to use a USB modem (Smartlink). The modem installs ok and works fine. However everytime you reboot the pc and then try to connect via the modem, it reports as "unable to establish connection". I then...

HI Thanks for your replies.. After reading some of the other posts I realised that it was the normal.dot template that needed changing, but thanks for the confirmation Cheers Wookie27

Im sure there is an easy way to do this.. but I have not found it yet. When Word starts up the font automatically defaults to Times new Roman. Can you configure Word to automatically start up using a different font type / size etc.. ?

Hope somebody can help with this. For the past year or so I have been connecting my digital camera via USB 2.0 to upload photos etc.. This has not caused a problem before and it correctly creates a removable drive volume F: each time its connected, which I can then access its folders under. I...

If I have understood your post correctly then I am confused as to why you have got a another default route pointing to 10.4.5.0 ?. When you create IP addresses on Vlans, routing between them is automatically turned on. Therefore from what you have stated you already have a vlan within the...

I think the default is 25 Seconds. If you look at the TFTP values on Sitemanager, it has a retry timeout parameter of 5 seconds which specifies the number of seconds TFTP waits for an acknowledgment before retransmitting the last packet. And a retransmit value of 5 which is the number of times...

I take it you have a quad ISDN card in your ASN. If so you have to create a bandwidth pool in which you place the other ISDN circuits. Then for your initial demand circuit you click on the BOD "Bandwidth on demand" button on thedemand circuit definition and choose the bandwidth...

Check that the port you are trying to enable diffserv on is not a member port of an IP filter already. If it is you have to go into the filter itself into the port members tab and disable the port there. Then go back and change the diff serv settings on the physical port. Finally go back into...

Yes you are right the newer enhanced modules end with a E on the card number eg: 8648E.. this will allow ingress & Egress port mirroring

What I would suggest is that you just put a single word in as a interface name eg Test1 with no spaces , save the config and reset it and see if it appears. Or if you need more than one word to describe it use an underscore eg. Test_name1. Try this and let me know if this works

If You have the Ip addresses showing then its not going to be a default config issue. What Accelar model are you using and what is the software version. Something at the back of my mind is telling me I may have had a similar issue a long while back when the boxes first came out. I belive...

Are you saying that there is none of the info you entered in the config? if so... Make sure that the factory defaults flag is set to false. When it starts to boot it will prompt you to press any key to stop autoboot. Press any key and it will take you into the monitor mode monitor> then...

Just to add to this thread... at present SMLT is a propriety protocol to Nortel.. Therefore you can only run SMLT between two Nortel switches which support it. However MLT is a standards based protocol (though it goes by different names.. Cisco call it EtherChannel I belive) which you can use...

Sorry forgot to mention that its outlook 2000.. I ahev seen another thread relating to this problem but that with Outlook 2003. The fix they suggest there indicates that i have t set up a HTTP server though i do nto seem to have this option on 2000.. or if I do I cannot find it

Is it possible using outlook to download hotmail into MS outlook. I already access different email accounts by setting up the relevent pop/smtp servers in the mail accounts section, though I cannot seem to find the POP or SMTP servers for hotmail. Any ideas if this can be done and if so how ?

Sorry .. forget to add this.. Unless you have a L3 switch which will route internally between Vlans, for every Vlan you have configured on th eswitch you will need a separate router interface. Although its possible to multi-net an single interface (that is apply more than one IP address to an...

This is really only possible if you have two ethernet ports on your ARN, if you only have one you can purchase an additional module to fit into the expansion module. Assuming you have two , configure the IP address of the subnets you want on each interface and then plug a patch cable into each...

Also make sure that the port your pc is connected into is is a member of that Vlan.. the "show vlan info all" command will be able to tell you this.

What you also have to bear in mind is,if you are dialing another Nortel router remmber to configure the remote end to have a bandwidth pool. Therefore if the remote router is a Nortel you need to do the following. On the router which initates the call , on the demand circuit, click on the BW...