Search results for query: *

on our trace, i see invalid codset5 ... have you tried codset6 ? that change is located in on page 1 of the trunk group and it is about 2/3 of the way down on the left. typically in the US, we do codeset 6 (sometime 7)

46xx VPN client is still in trials. We have been using SONICWALL (before that Ravlins) since 2003.

In ASA ... go to advance tab export data select the station object to export select the Export to LDAP directory

when a clan is restarting state, ping will not respond. If a busy board and a release board does not do the trick, you will need to reseat the board to let it restart. the key is fixing the restarting problem first. you mention TN799DP ... What type of carrier ? If it is a G600, CMC1...

did you try changing that to codest6 ?

changes to codeset XX is on page 1 of the trunk group and it is about 2/3 of the way down on the left. typically in the US, we do codeset 6 (sometime 7) so without understanding what you have it is hard to tell you, but trying codeset 6 (more common) might help. I don't know what codeset5 does...

your comment ILEC implies that you are using someone other than AT&T, MCI or one of the Bells. usually an ISDN cause code of 1164 means that your ILEC is not keeping up with the ITU-T e.164 or the North America Numbering Plan Administration changes. The other possibility is that the far end...

The directory feature in the Definity is strickly a 1 to 1 as each name uniquely maps one extension. That's is what it is designed for. It was never intended for multiple people sharing a single extension. The last, first is what you put into page 1 of the Station under name form. What i do...

going into the gateway and doing a reset system 4 is prior to CM release 3

go to page 3 of the analog station form and towards the bottom there is a hot line feature ... Place in the dial code to either the system list or group or personal list just the digit 9 (assume that your ARS feature access code is 9). When caller goes off hook, it will dial the 9 giving the...

list measurement ds1 log xxx and page a couple of pages forward and you will get to the current stuff. it keeps 48 hours. another way to look at this is list measurement ds1 summary and it will also give you a 48 hour window.

I am aware of this ... 'ch sys mg-recovery-rule-x' where x is the media gateway. The timer parameter there says 3 to 15 minutes. In your opinion, what is a reasonable number that you have been using or seen ? For the person asking the original question ... you might want to consider IGAR to...

Options ... you are using a Multi Connect Config and that means that you can share one IPSI per 5 port network (even in critical reliable), so long as it is per PNC. For tone, you can rely on call classifiers, thus lowering your cost. I chose to go with IP connect and I do suppliment...

u need to restore it to both system on the s8700. DO NOT SAVE TRANSLATION, as it will overwrite it. Thereafter, go to the WEB and restart system. When system comes back up ... use ASA and go take a look. alternative u can also do it on the active processor of the s8700. but first you must...

i am assuming you have a release 9.x switch ... the command to display dial plan is display dialplan it will look like this ... Digit - 1 - - 2 - - 3 - - 4 - 1: misc 2: misc 3: misc 4: misc 5: misc 6: misc 7: misc 8: misc 9: fac 0: extension *...

If all else fails, have you tried your VPN on a known ISP that works, because some ISP do block tcp port 1720 for call control and maybe h.323 protocols or Port range between 1025 to 54535 for the audio part. This way, you will eliminate that its your PC and therefore, isolate your problem to...

Long time ago, I have worked with CENTREX connected to G2/G3. It is basically the same. There is really no difference between and ISDN PRI to the PSTN and one to the Centrex PRI .. cause at layer 1 and layer 2 its the same. Most likeley you will be going with NI-2 and all that stuff. At the...

If you are running XP Professional and you do not have QOS RSVP turned on in Windows SERVICES (either as manaul or automatic) and your run your softphone R4 or higher, it will fail and close. At a minimum, you will need to have services turned on as manual. Also, have you looked at the...

are you running windows xp ? if so, did you turn on QOS RSVP under services ?