Search results for query: *

you can try to set up message forwarding. NTL555

are you intercoming the extension? I believe a digital phone can not pass DTMF tones to an Analog Set when you are in intercom mode. I haven't had issues with passing DTMF tones through GASM or ASM8+. NTL555

Cheers to that. I love no longer looking in the manual for dip switch settings. I never put in a FEM module as well in a 450, but I guess I will have to try once my FEM comes in. Thanks for all the help! NTL555

Thanks for the response... I called it the old legacy stuff because the BCM 450 uses slot instead of buses. The old BCM 400 4.0 would use bus number 2 thru 7. If you wanted to use Bus 2 you would set switch 1 on the FEM module on and the rest off and if you wanted to use Bus 3 you would set...

I read that as well in the installation manual. My question is that if you max out all the bays with the FEM installed in the BCM 450 (10 bays used).. does that mean you have an additional 6 legacy modules available for use. NTL555

I know the FEM module on the BCM 400 required a DS-30 bus for every dip switch set to the on position, but the BCM 450 is different. The manual says to have all switches on and configure it in the manager and the limitation is 300 sets, but my question is about capacity on that FEM and the BCM...

As far as I know... I don't think so. If you don't program anything it goes to General Delivery. NTL555

its under Hardware under card 1 or 2 for Module 2. You must have the PRI Enabler Installed. for SLI you must have the MCDN Keycode installed. NTL555

Another Update. I had 5 more of the ASM8+ in stock and each had to be inserted HOT for the system to even start the firmware download and to be recognized by the system. I dont know, but hope this helps anyone. NTL555

I think that number is for only download, but it will depend if you actually get 3Mb up and down and what actually goes across that. Each conversation takes up 64Kbps up and down but you will still need a router that can handle quality of service. You can be watching Youtube and your...

To me, it works fine, just got to make sure you implement QOS, establish a VPN between all locations, and make sure your data bandwidth is good. NTL555

Snowman, yes it did show "started firmware download." Funny thing is once I inserted the card live, the BCM started to download its firmware and within seconds the MBM came right up. I did attempt to configure and then install the module on Friday, but it didn't work. I will try what you...

If you have a Call Center application, the customer will hear music on hold until the next agent is available to take thecall otherwise, if a caller is being transferred from the AA or a receptionist, the customer will hear ringing. NTL555

F983, log in with your UserID and Password, then hit AA, then hit Grtg, hit Grtg again, and choose your greeting. This is only the company greetings and not the custom routing prompts. NTL555

Update. So I've tried everything I knew what to do and do not approve what I am about to tell you, but it worked. I got frustrated and took out the module hot (which I personally hate doing), double checked my switches, and inserted the MBM while the system was powered up (which I do not...

I read that part as well and tried it hoping it would work, but that I believe only applies to adding stuff in the Expansion unit. The doc says "If you are installing an MBM in the main unit, the MBM must be installed before it can be configured. If you are installing an MBM in the expansion...

The Power LED on the ASM8+ is a solid green but the Status LED is constantly flashing green. It never initializes. Originally I thought it could be a bad slot, but attempted to de-configure the module, change the module to None, and then shut down and inserted a DSM32+ and a GATM8 in its place...

Dallas, Texas with a BCM purchased in North American. NTL555

I can not get a ASM8+ to work on a BCM 450 release 1.0. Yes... as simple as it may seem, I can not get this to work. Updated with the lastest patches, installed the element manager from the BCM 450 after the patches, all my six dip switches are in the On position on the right and the other 8...

I had this problem... performed a Level 2 reset and then replaced the hard drive when the system was stuck in a endless loop. Check your sata connections as well. NTL555