Search results for query: *

Hi Can I outpulse an * or # as a part of dialed number over a PRI trunk?. How i can do that? For example *40*458... as calling number. It's for activate a feature in CO. Thank's

Unkalary: Thanks for you tip!!! It's the solution!. The system always show me the slot how a analog card (16 ports). I follow you tip and there is no problem now. I was try to back to digital card and I was build a digital unit on the slot, then I erased it again but this not fix the...

Nortellian: Nop, I was erased all digital unit from the card before replace it. Thanks. Capipo

stroked5o: Yes, I build a unit on the analog card, I try two ways to enable the port. when I try to enable the unit with enlu x x, the stat shows that the unit is enabled (idle) but without dial tone. If i try to enable the complete card with enlc X, the system after few seconds show me...

HI I have replaced a digital card for a analog one in a opt 11C system (rls 25.15) but there is no dial tone on any port. I was changed the card (a known working card) and anything happens. If I change the card for a digital one on this slot, the ports works nornally. When I try to enable the...

HI: The only way I know to adjust meridian in time is a command in LD 2 SDTA x yyyy where x is the increment positive (1) or negative increment (0) yyyy is the adjusteent in increment of 100 ms. TDTA to print the current adjustement The adjustement is produced during midnight routines...

HI wdhb! I've MAT tool and receive SNMP traps from few option 11C. The question is, sometimes I receive traps, ie with error code= BSD090 Main Cabinet Power Fail . The problem is meridian not send a trap when the power is OK. Exist a way to check from TTY if power is OK? There is some...

Hi: Somebody can tell me if there is a way to check if power on the swith is up remotely (ie modem)?. I receive BSD090 alarm but i can't check if the power was back. Thank a lot.

Check TGAR config at the route and TARG on the set that make the transfer. They must be different. If you have a TIE line check LD 15 CCS DATA TRY CCRS=TLD (Must be different of FR2)

Hi! I have a rare problem when somebody make a transfer. We have two Option 11 Rls 25.15 conected togheter with a E1 Tie MFC-R2 and one of the systems is connected to public net with a E1 DID MFC-R2. The problem is the follow: In a incoming call from DID trunk to a set on first meridian the...

Perryp I don't have a tape drive, which might be it? and Which is the procedure or where i look for information about this?? Thanks.

HI I've a Option 11 C 25.15 with mmail 13 installed. The Hard disk of mmail is damaged (I don't known how) without posibility of recovery. What do I've to do to reinstall mmail?? What equipment is necesary to do it?. Thanks in advance.

Set bit signals in E&M with R2?? are you sure? Don't Care Check in LD 94 REQ PRT Type R2MF ICOG OGT --> Outgoing table TBNO 0 --> The table number used in Route (ld 16) ... Look at level 2 (LVNO 2) Received signals RECV 2 OUTT 3 BUSY 4 CONG 5 VACC --> SET THIS IN YOUR...

HI This is my conf. Trunk TN 9 1 DATE PAGE DES TN 009 0 00 01 TYPE RAN CUST 0 XTRK EXUT TIMP 600 BIMP 600 AUTO_BIMP NO RTMB 30 2 DATE 11 SEP 2001 Route REQ: prt TYPE: rdb CUST 0 ROUT 30 TYPE RDB CUST 00 DMOD ROUT 30 DES MIRAN TKTP RAN NPID_TBL_NUM 0 RTYP CON GRD...

Sevensen. Look at my response to Rookie10 2/24/03 "Creating New Clid Entry" on this forum. Capipo.

Rookie The entry 0 is the default when you configure a new extension. You can change it in LD 15 NET_DATA (Sorry, i don't said it you before). If you want to create a new entry like entry 1 you should change the configuration of each extension in the system, like said Janaya: KEY 00 SCR 1234...

It's depends on the type of signalling that you are using. Also depends on your internal numbering plan, it will be on the range assigned for your telephony company provider. They validate only these range of numeration. If the trunk is an MFC signalling type, look at prompt CNDN in LD 15...

I need only know the amount of calls to/from a specific TN. One of the solutions will be to read the CDR's, but the only one conection with the system I've is MAT via Ethernet. In MAT I don't have Call Acounting, but in the menu Utilities i can open "Data buffering & Access". When i...

HI I've a serious problem i think. When i try to backup the config in LD 43 EDD, the system show this message: RPT: Can't create log file c:/u/rpt/rpt.log (errno 0x380001) and TEMU107 PSDL file can not be open or not exist in the system It's so serious how i think?? How i can resolve this...

Thank's John! But I want to use MAT Telemanagement traffic Analisys to do that. It's is possible?? Otherwise I'll use CDR's with the utility you mentioned. Thank's again. Capipo