IP Office is doing DHCP. Most everything on LAN1 tab is default. IP range set to hand out 50 IP Adresses. Only 32 phones.
46xxsettings file is default. Phones upgraded to 6.3116 normally.
Gwebster 6.3116 for all phones on system
intrigrant error on phone is cannot find call server before...
IP500V2 R9.0 SP5 IP Office doing DHCP
Had a 9641 that got stuck on waiting for LLDP. Other 9641’s at install DHCP’d normally.
Statically assigned new 9641 and it worked.
Took 9611 that the 9641 replaced, cleared settings, installed. DHCP normal. Phone came up normal.
The only thing I can...
Had a DS30B that we could not downgrade from 9.0 to 8.1 using Manager. Did not see PCN on this until... DTE into DS30B and use AT commend. Kept coming back with the word ERROR and brings you back to a -> prompt. Same with any other AT command. Type help get a bunch of commands. One was upgrade...
I have used a hunt group with all users in the group. Then setup a short code for Dial Paging to the hunt group. When you dial the short code your voice comes out over all the idle digital handsets. (have not had the chance to try it over IP sets)
For an emergency message over paging the Viking...
Anyone seen or know of this problem?
PRN: FEC::TransmitterError FEC=2 BD=0x0C40 fcce=0x001c0000 trans=54 producer=52 consumer=62 chipbd=18665c88 nextbd=18665e80
Just a guess but does the above indicate FEC (Fast Ethernet Controller) 2 (transmit error) that the IP 412 tried to transmit info to...
I used 2 analog station ports configured for loudspeaker paging. When both are included in the same group both phones just ring (according to SSA). If I take either phone out and leave one in, the paging works.
Is it possible to add two paging speaker extension ports to a single hunt group with users in it? I tried this and both paging ports just ring. When I add users the users hear the page but nothing over the page ports. Take all users out and put one or the other page port in and it pages to the...
My bad, I found out something new.
The short code works if you call an extension from an extension using the short code.
It does not work if the call is from the outside and the call is transferred using the short code.
Hairlesssupportmonkey,
I know it has not changed. I put the code in a release 3.52 as 8XXX | Dial Extn | 8Nt(1) | 0 to limit calls to extn 8XXX to one minute.
I put the same code in a 500 with 5.0(8) and 8.1(67) and it does not work.
I was wondering if anyone has actually got it to work in a...
This feature used to work in 3.2 and lower.
We cannot get it to work with 5.0 or 8.1 (the release I have in my office and the release on cust site)
Has anyone tried this feature on 8.1 yet? and got it to work?
ghidra -> I did not check the speeds of the ports. Someone else set the extreme switches up. These are old switches that were upgraded to the latest firmware. Echo is on external only.
Justatec -> We were set at 729 then went to 711. Customer said call quality was much better. I also tried the...
sagbab -> Tried what you said the day I put it in. Also tried creating a new user. No avail. Tried another 5610 today. Same thing. I think it is a software bug. The first 5610 was at 2_9_1 firmware. The second was 2.887 and would not upgrade. Checked all the obvious and the correct files were on...
I already tried a reboot. It did not fix the problem. We do not believe the echo is on our side since there is no echo on internal calls. The voice and data networks are totally separate using different equipment. We are in the process of working with the local dial tone vendor about the echo. I...
This is the upgrade track for a 412
Multi-Stage Upgrades
Due to the need to adjust internal memory allocation and configuration storage, for some upgrades the control
unit may need to perform multi-stage upgrade process. The table below indicates the require upgrade paths.
Control Unit IP412...
Having major echo problems on a 6.0 so we upgraded to 7.0 to see if problem clears. (It did not) Also running all 9620 sets. Tried installing a 5610 just to see if the phone model made a difference. But after installing the extension number comes up but no buttons are programmed (Manager says...
Does anyone know what this means or can point me to a document with information about these types of alarms?
Abnormal termination
Termination cause: <Machine C> addr=00000000 d=5 pc=f01ff98c f033ade0 f033b1b0 f033b2c4 f03985dc
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.