Search results for query: *

Got it. Apparently something was screwed up with the BootP in Manager. I downloaded a different BootP server, and the 500 downloaded the file immediately. Apparently, the IPO 500's responses to DTE commands (AT-X, etc) are different, but the result is the same. Also, I figured out a...

Having a problem with an IPO 500... I have 2 DS-8 boards, and 2 Legacy boards, each with an ATM-4. When I boot up, in SSA I see the two ATM4's and the two DS-8's, but in Manager, no lines appear on the "Lines" form. I have tried swapping which module bay the cards are in, (3&4 with 1&2)...

We're getting it to work on IP Office with NO WebLM Server.... therefore no license neccesary. If we don't give the phone a WebLM server address, it doesn't ask for one, and it doesn't say that it'll only work for 30 days... Is this working as designed, or an Avaya 'oops' ?

enet - did you ever figure this out?? I'm trying to hook up a Fax Finder from MultiTech; same idea... we got a VMI, and I was travelling down the same path (fwding virtual numbers), but I'm stuck... You get anywhere with this one? Thanks, Jon

Yes, the Fax Finder works with Key Systems as well. The requirement that MultiTech gives is that the system must be able to deliver calls sent to many DIDs on through to one or two extensions. I'm having no problems with this part, it's just that the MICS isn't sending the DTMF tones on down...

Oh, here's a link to the FaxFinder's webpage... http://www.multitech.com/PRODUCTS/Families/FaxFinder/ Thanks again, Jon

Hello! I am trying to configure a product called a FaxFinder by MultiTech on my Norstar MICS. The way this product is supposed to work is as follows: A block of (40) DID's are pointed to my MICS over the PRI. These 40 DID's are pointed to two DN's on an Analog Station Module, and these two...

Tried that, actually it didn't work.... Any other ideas?

Is there any way to cancel a system reboot when free after you have set this? I know I can just leave a phone off the hook to keep the system busy, but I want to cancel this request. Can anyone help? Thanks, Jon

On the extension form, the 'Caller display' was 'Off', and I switched it to 'On', but with the same results. I have always gotten the caller ID info at the bottom of the screen, just not next to the call appearances... Any other ideas??

It was set to 'off'... what should it be for the 5420's? Thanks, Jon

We just installed an IPOffice with ~120 stations, and none of the 5420 sets display the caller ID info next to the Call Appearance buttons when the caller is placed on hold. We then tested this on our in-shop IPO on an older VOIP set, and it worked fine. Is this a firmware issue, something...

Have people received an email with reports form this thread? I don't see the website at http://www.iporesource.com/ being up yet... what's the status of this? Thanks, Jon

Thanks Surplus!! That worked great!! Jon

Is there a way to cancel a wakeup call? In 'display display-messages auto-wakeup-dn-dst', there is the message 'Wakeup Request Cancelled', so I would assume it's possible, but there seems to be no label for this in the button programming... Is it done by a certain keystroke in the wakeup call...

Marv - Thanks for your reply. I have re-terminated this in the closet, but I'm getting the same results. I have used different wiring to another jack with the same results, so that eliminates the station cable. As far as the amphenol, I can't take everyone else down to re-seat that at the...

Sheesh, a year and a half later... This problem has been dormant for a year and a half, and just came back this week. We just added several new users to our Norstar MICS 4.1 system, and ports that had seemed to be working fine are now acting up. When the handset is picked up, there is no...

Sheesh, a year and a half later... This problem has been dormant for a year and a half, and just came back this week. We just added several new users to our Norstar MICS 4.1 system, and ports that had seemed to be working fine are now acting up. When the handset is picked up, there is no...

NANPA, the North American Numbering Plan Administration, is the authoritative source of NPA information. Check it out: http://www.nanpa.com http://www.nanpa.com/number_resource_info/area_code_maps.html Jon

tiggermanh - I'd try re-posting this as a new thread... I'm not sure what's up with your system, but I know somebody here'll be able to help!! Good luck, Jon