Search results for query: *

Our PBX Meridian CS1000M Version 3221 Release 400T When set up call forward to external for DID line, the caller info show on the far end is the site primary info, instead of the actual caller. Is the system able to send the original caller ID?

Thanks all! We have 2 PRI lines as incoming route, the other PRI works fine when this one has issue. I swapped these 2 PRI lines once on the CSU/DSU end and the PBX card end, so I'm pretty confident the issue isn't on these equipemnts. As John mentioned, it still could be on DMARC which I have...

For the last 10 days, one of our PRI line has red alarm issue so frequently. Based on the history file, it just went up an down every few hours. See below. I called the telco but they always said they reset the circuit and the service came back, but never fixed it 100%. Any suggestions...

Thanks All! That makes sense.

DID Range: 123-456-78xx (00~99) extension range: 7800~7899 Here is the RDB and DID setting: TYPE RDB CUST 00 ROUT 1 DES TKTP DID M911_ANI NO M911_TONE NO NPID_TBL_NUM 0 SAT NO RCLS EXT VTRK NO NODE DTRK YES BRIP NO DGTP PRI ISDN YES MODE PRA IFC NI2 CBCR NO...

Thanks John and Bryan! Can you post an example of the details setting for LDID? Thanks. In my Nortel setting, I created AC1=9 and SPN 1305666 routing internally to Cisco CM. And we didn't configure LDID for 212973 before.

3 sites: Site A: Cisco CM 4.2 (212-555-75XX) Site B: Nortel 81C (212-555-79XX) Site C: AVAYA (305-666-45XX) History: Site A and B are in the same building, connected via PRI link, routing plan had been configured, user can dial to each other directly by 4 digits extension (75XX and 79XX)...

you are right,I searched several posts here regarding ESN0086 error, it also indicate that 64 is the limit for one SPN entry.

Just got an error code after I input 64 records. ESN0068 No more restricted numbers allowed for this code. Do you know how to increase the numbers? Thanks,

I have about 100 numbers/number ranges needs to be input as ARRN in one SPN, is it possible? ie. SPN 212 RLI 1 ARRN 654 ARLI 2 ARRN 6543 ARLI 2 ARRN 6544 ARLI 2 ARRN 6543210 ARLI 2 ...

GHTROUT you are right, the PRI link channel on the far end PBX doesn't have enough COS. Thanks!

We have CS1000 connected to far end PBX via PRI linke (Rout 30), each side dials to other side by entering 4 digits extension number. Now we plan to route all outbound calls to the far end pbx to using their trunks to call outside. I configured this in CS1000, but it failed and gave me fast busy...

Yes, i'd like to transmit all 91202xxxxxxx numbers to AVAYA A to handle the call routing.

NYC: Nortel CS1000 using PRI link connected to AVAYA PBX A, each side can dial to other end directly by extension#. DC: AVAYA PBX B AVAYA PBX A&B connected via IP trunk, A had been configured to using B’s outbound trunk when dial DC area numbers, 202 etc. We plan to configure the PBX to also...

Great! You guys are AWESOME!

Nortel CS1000, 1 T1 PRI trunk (RDB 1) carries outbound call. Now we plan to set up 2nd T1 trunk (RDB 2), and we want to have all outbound calls to 404-335-xxxx and 404-661-xxxx to be routed to 2nd T1 trunk. How to change the ESN setting to have this feature work? Currently setting: AC1: 9 SPN...

Thanks GHTROUT!

As I know, changing in LD10 for telephone will disconnect the call, but I'm not sure if I change the setting in LD16 RDB will also disconnect all chanells in that route group? Thanks for your confirmation!

GHTROUT: ~~ Defined in separate/different loops, and neither in Shelf 1 (prefer shelf 0) of their loop. Good remind! Another question: Will the incoming call rings at both console A & B at the same time, or in somewhere I can configue the sequence?

If I have 2 receptionists works on different floors. I want to set up each receptionist with a M2250 attendant console. The company has several primary phone numbers, so during the daytime, all incoming calls will be distribute to 2 receptionists by the number. Here is the setting. Is it...