Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. PrivateBuild

    Phone restarts after Extn Login

    It doesnt seem to be switch related. This is raised and has been reproduced by Avaya CQ45526, though not listed as yet Was raised on 6.0.14, havent tested on 6.0.18 but i dont think there was time to have it included ACA ACS ACI
  2. PrivateBuild

    SBM24 on IP Office

    Make sure the firmware on the handset is correct for the build you are running on the IPO. If it is 6.0.14 the handset should be 3_11 which will show as 3.110b in SSA ACA ACS ACI
  3. PrivateBuild

    Caller does not hear rings when Cfrwd is enabled to external #

    Change or create the shortcode so the forwarded call is not going out via the ARS table. ACA ACS ACI
  4. PrivateBuild

    VPN handset to Snapgear 580

    Hi, Has anyone successfully connected a VPN handset (using VPN firmware from 4.2.14 build) to a SecureComputing/snapgear 580? Version on the router is 3.1.5u1 Cheers ACA ACS ACI
  5. PrivateBuild

    CCV cant connect?

    Did you change the Access permissions on the CCC folder and on the client PC as per the install manual? ACA ACS ACI
  6. PrivateBuild

    IP500 CCC Loging in and out

    Dont confuse "log out" with "Busy wrap up". If you disable your membership in one hunt group (busy wrap up), you will disappear from this hunt group in CCV as you can only be seen in one state. For example , you cant be seen as ready in one group, and busy wrap up in another. For a test, put the...
  7. PrivateBuild

    Queue Messages

    You should be able to do what you want within condition editor and compare. By using the new $TIMEQUEUED and $TIMESYSTEM variables in 4.1.27 VMPro, i think you will be able to achieve what you want. You will just have to work out the timings between the messages and all should be good. I think...
  8. PrivateBuild

    Call Center View - Alarms

    Hi, You can set the display time for the alarm under the Alarm settings tab. The audio alarm is only for the PC running CCV. You can set an alarm tone from the wallboard server, but this is only for wall mounted Wallboards such as the Ferrograph. Cheers
  9. PrivateBuild

    IP Office Crashing

    The last reboot in the error list shows you are running 3.1.65. The next build which was 3.2.17 addressed a couple of TLB reboot errors and build 3.2.55 addressed even more. Suggest you upgrade to at least the latest of 3.2 (67) or higher still to 4.0.14. Once upgraded check you config for...
  10. PrivateBuild

    CCV access from remote client machine

    One setup can be:CCC is installed by the book on one subnet. Just need to share the CCC folder. Then on the the client PC in the other subnet we had to put the CCC server name and ip address in the host file to allow CCV to work (\WINDOWS\system32\drivers\etc\hosts)
  11. PrivateBuild

    VM PRO update error ...call flow database error

    How did you connect to the VM computer? Corruption can happen when connected via Remote Desktop (not supported). Tha flash screen at the start when you open VM will show corrupted characters. If it has been corrupted, you will have uninstall / re-install. If you have exported the database...
  12. PrivateBuild

    Phone Manager and Voicemail

    Not at this stage via Phone Manager.
  13. PrivateBuild

    IP500

    You are not meant to be able to barr extension to extension dialing, but on 4.0.5 you can make a single digit shortcode that works. Havnt tried on 4.0.7 yet. For example if your extns are 2XX the shortcode is SC:2 Tele:.(or blank) Feat:Busy You may want to reduce your Dial Delay Time or Count to...
  14. PrivateBuild

    Out Of Service fallback

    Are you using VMPro for the AA? If so, you can point the ICR straight to a call flow to the Hunt Group and create a user variable you can test to switch the destination when required.
  15. PrivateBuild

    How to find out IP of IPO

    No , you wont need any AT commands to view this. Just have the Hyper terminal/serial port settings as: Bits per second 38,400 Parity None Flow Control None Data bits 8 Stop Bits 1 Settings | Emulation TTY Connect and power up the IPO and you should get the full DTE output
  16. PrivateBuild

    How to find out IP of IPO

    Yep, in the DTE output you will see an entry for LAN1 and a hex output next to it. Type the hex entries into the PC calculator and change to decimal to see the number.
  17. PrivateBuild

    CCV Not Working on Client Machines

    Have you adjusted the Access Permissions as per the installation guide (pg17)?
  18. PrivateBuild

    eMail action in VM Pro

    To use the Success /Failure of the Leave Mail action you need to running in IP Office mode. If you push "0" whilst listening to the message you will follow the Failure path. If you push "0" after listening to the message and the after the tone, you will follow the Success path.
  19. PrivateBuild

    Help with SMTP

    Does your email account have a first name and last name? And when you choose it from the Email settings in control panel ,do you use the browse function to choose the user? If so,voicemail pro will put the name in with a space and SMTP wont accept it. (it puts a + in place of the space)...
  20. PrivateBuild

    PC Wallboard Displaying Queue

    adirondackman, This issue has been raised with Avaya and is due to be fixed , along with a heap of other things, in CCC 5.0.43 which is in field trials now and due for release 28th Feb. [smile]

Part and Inventory Search

Back
Top