Search results for query: *

I have a Cs 1000 release 5.5 and two sites that have BCMS. We have trunked them together using NRS service. One site when using the G729 codec will drop calls to certain area codes and prefix , but not all. The other site works perfectly using G729 codec. Both sites work correctly with G711...

Great thanks, the Intels are hard to find

Intel 80 gig ssd sata 2 using clonezilla custom sector by sector clone worked great samunsung sata 3 drives would not work

Have a strange phenomenon. Cs 1000 set up with vlans. From the data vlan I can ping the s1 server on the tlan vlan, I can ping the mgc cards that are on the Tlan. On the sig servers I can hit all the devices, but cannot ping the default gateway that is programmed on the Tlan Vlan. 5520...

Thanks for the try, the cable spec I am looking for is the serial cable that connects two digital mobility cabinets togther, the cabinets are dmc080.

Does anyone know the pinouts ona dmc link cable Very hard to find now, I wonder if I can make one ?

They start at the lower right hand side and go up. 6 3 5 2 4 1

Thanks for the insight. That is very helpful.

Being an IT guy thrown into the world of phone programming, I had a couple of questions for the old hands here. I have got the basics, target lines, voice mail, auto attendant etc. But some of the finer points I could use some advice on: When to use scheduled ringing service versus hunt...

Thanks It was an id10.t on my part I had to deconfigure the card to change it to pri Thanks for the responses!!

Hi I have installed a DTI card in a bcm 450, but it shows as a T1 card and no way to change it to a PRI, do I need a different card or is it a dip switch ? (I am not sure if they are all on)

Even if you have a POE switch you have to use an external power supply. The PS hooks up to the phone but powers the KLM backlight. same power supply as the POE for the set.

Does anybody know if the 1102e will support the usb headset on the BCM platform, I konw the 11402 does, but can't seem to find an option for it in the 1120 interface, though it recognizes it in the usb sub-system

I have done this more than once, the only caveat is if there is heavy data use also then qos on the network and the wireless bridges is very important.

On the BCM 450m the slots start from the bottom 1 through 4. Make sure you are provisioning the correct card using this information. It got me for a few hours today until i figured it out.

Well I was able to change the default vlan on the "trunk" port on the 1020 to the voice vlan, but it made no difference in the performance of the swicth in our environmnet, I still can make a call out the pri to a number, it calls and answers but no audio is passed either way.

Ah One more question, how do you chnage the default vlan on the 1020 port? There is no way to change it that I can see. I tried deleting it out of both vlans and readding it in, but it hangs on to the defalut valn of 1?

Thanks the only differnce from my config to yours is that the default vlan for the uplink port was the data vlan (1 for me) rather than the voice vlan. I will reconfigure the 1020 with that in mind and see what happens. Thanks much !!!

Thanks for your reply. Egress tagging is turned on on the 1020, The 5520 is acting as the core switch routing is enabled and 6 other 5520 have a trunk port setup to the core and are working perfectly. We have full dhcp working with the custom scope to correctly switch to correct vlan. The...

Thanks, for the tip. When I repalce the BES 1020 with 3 com switch in the same ports I get to all services correctly and am able to make calls normally out the pri. I replace the switch with the 1020 no audio no call pilot, but the call signaling works and the numbers are dialed and ring, but...