Search results for query: *

Does anyone know where to disable the CO Admin Audit of the VAS-ID.

Thanks. Here you go. ADAN HIST SIZE 65000 USER MTC BUG ADAN TTY 0 CTYP QSDI GRP 0 DNUM 0 DES POWER_MONITOR FLOW NO USER MTC XSM YES TTYLOG 0 BANR YES ADAN TTY 1 CTYP QSDI GRP 0 DNUM 1 DES CDR_Pollcat FLOW YES BCST NO USER CTY XSM NO...

I have looked at thread798-1289561 and my problem is that I have MM on a 81c and the message is every 1 min; this has been going on for sometime now and I have sysloaded the switch a few times since. I only have one active AML port which is for MM. Does anyone have any suggestions where I should...

One thing only rel. 12 and 13 of MerMail will work with succesion 3 and 4.

I HAVE EVERYTHING SETUP CORRECTLY FOR CALL FORWARDING BUT MY PROBLEM SEEMS TO BE NO FREE LINES WHEN DIALING OUT WHEN THE CALL IS FORWARDED OR TRANSFERED. I HAVE A PRI WITH 20 DIDS; LINE 145 THRU 164. THEY ARE ALL TARGET LINES. LINES 001-023 ARE ON PRI-A BUT ARE UNABLE TO GRAB A UNUSED LINE TO...

Does anyone no what version 30NdG00 is? Thanks,

Is it possible to move everything built on a line card to another card? Without moving every TN one at a time.

AUD0422 a b c d e f g h i A call with MAINPM = .REORDER was found not to be receiving nor waiting for overflow tone. Overflow tone will be given. Where: a = CR Addr MAINPM/AUXPM b = Originating Type c = Originating TN d = Terminating Type e = Terminating TN f = QUEUE IN g = CR Dialed DN h =...

As long as your second line is on key 1 then LHK=1 is O.K. Are you sure you are not using meridian mail for your voicemail system? If so then make sure that the mailbox has included your second line as an EXT.

WHAT IS YOUR LAST "LHK" SET TO, AND WHAT TYPE OF VOICEMAIL SYSTEM ARE YOU USING?

I have the target lines set for appear and ring and have tried line redirection; still no luck.

I think I have one that will stump most of you; I have ICS 4.1 system with a PRI programmed for NI2. When I forward a desk phone to a cell phone and 4 digit dial that ext. from another set on the system the call is forwarded out of the switch correctly and call is completed to the cell phone...

Yes; it is called a ATA adaptor.

I would like to know how to disable long dialing on specific set. Does anyone have a suggestion?

Calls coming into the main number and after a specified number of rings go to a voice mailbox.

Is it possible to setup a voicemail box on a 2250 console?

Over the past 2 days I have had some of my printers LPR ports just disappear. It appears to only be happening on two specific subnets. The next day I have to go back in and recreate the ports. The printer names are still there. All my other printers seem to be fine. There is nothing I can see in...

We have Muzak on all of are switches and every time they installed a unit the volume was to low and we had the vendor install a preamp and a volume control knob.

Hey John I have already built the CLID table for the 2250 but do you know how to apply it the console? I have not been able to find where to do that. What I did as a work around was change CLID table 0 for the 2250 and assigned CLID table 1 to all my other units. This was the only way I could...

Does anyone know where I can change the which CLID entry my 2250 pulls?