Search results for query: *

I have a client that has a Partner ACS and MAIL unit installed. They recently wanted to have a same greeting play day and night. I recorded the greeting in AA2 and assigned the lines to answered by AA2 and the MAIL unit after 6 rings. The problem is that an unknown AA greeting answers during...

The messagenet is basically a an OPX on teh system connected to the system by incoming DTI trunks. When the Messagnet goes offhook, it pulls dialtone form teh Option 11 to make internal calls. These internal call work fine, but when it tries to dial 9 for an outbound call on RDB 1, it...

Here is the RDB for the messagent trunks It was listed above. REQ: prt TYPE: rdb CUST 0 ROUT 35 TYPE RDB CUST 00 DMOD ROUT 35 DES MSGNET TKTP DID NPID_TBL_NUM 0 SAT NO RCLS EXT DTRK YES BRIP NO DGTP DTI ISDN NO DSEL VOD PTYP DCO AUTO NO DNIS NO ICOG ICT STEP ACOD 4616 TARG 01 CLEN 1 BILN...

...RGV 640 FLH 510 GRD 896 SFB 3 TFD 0 SST 5 0 NEDC ORG FEDC ORG CPDC NO -digital trunks stat printiout- >ld 60 DTI000 .stat PRI* TRK LOOP 1 - ENBL FFMT/LCMT/YALMT: ESF/B8Z/FDL TRACKING SERVICE RESTORE: YES YEL ALM PROCESS: YES ALARM STATUS : NO ALARM CH 01 - IDLE DID...

hello everyone. I need some advice or help with a problem. I have an Option 11C that uses a PRI for DID/DOD in route 1 with ACOD 9. I also have a "messgenet system" that is connected to the option 11C via a T-1 DID. The messagenet system is used for automated messages to be put out over the...

I see, Thank you.

OK

If I print a TNB it will be 50 pages long since this is happening on various DID numbers. Most of which are 500 sets. so key 0 or key 1 doesnt make a difference.....

So,.... HTD in CLS and dont enter a HUNT DN, right? Then enter the FDN and set FBA and FNA in CLS. I'll try it.

I have a block of 200 DID/DOD numbers from my local provider. These nuimbers come in on 2 PRI's running NI2. The switch is an 11C with 25.40. I have several phones that are showing up as the main billing number when an outbound call is made. The main billing numberis 479-4232. I have the block...

I checked the packages on my 11C and found I have about all other packages except 120 which is the group hunt/DN package. I am out of luck unless my supplier can get me the package. Thanks for the help

will do the trac tomorrow when I get to site and can do a test on the actual trunks and stations

Thanks I will try that next time I am there

This is an auto terminated trunk to a dn that is assigned to an analog phone.

I need to start setting up group hunting in the Option 11C. What are the first steps to do this? I need to set "hunt" on some analog and digital sets to hunt to a group when busy or no answer.

Does any one know th pinout for the 616 caller ID interface? I inherited a client that has an old 616 with Disconnect supervision. I believe that GTE (VERIZON) installed the system about 10 yrs ago. anyway they have a caller ID interface that is currently working on the first 2 lines of the...

How can I make a COT trunk that is ringing into the system to receive a busy signal if the target DN is busy? Is there any way to do this? the users have this line coming in on a loop start trunk port but they are always using the PRI for outgoing and when they are making outgoing calls the...

no, we are not using DID, but the analog dn into a station port sounds interesting. not sure if the D/A to A/D then to D/A to A/D conversion will work very fast though.

...150 be programmed to trasfer an autoattendant call to the Fastrad? I am using a CAll Pilot 150 w/ 3.0 and a MICS with 7.0. I want to be able to call the site form my office and have the autoattendant send me to the rad for programming but i am not sure how to have the autoattendant dial F*9.

what type of interface? is it a norstar interface or a third party interface? Do I connect it to a station port or is there a serial port on the norstar cabinet that I use?