Search results for query: *

Have you enabled TLS 1.0 in AES? AES Web GUI > Networking > TCP/TLS settings Enable all 3 TLS versions

If your ARS code is say 9, then this will not be affected as the Adaption only applies to Pattern 0 (numbers starting with 0). Depending where you are in the world could be a different number plan, but thus would work for UK. Also it depends on what CLI you have received in the call inbox as...

Make sure you enable Port Redundancy first, this way the G450 will only allow 1 port active at once and leave 1 port in standby. Then I normally disable spanning tree on the gateway. Plug both ports into the LAN switch, you will see only 1 of the ports LED's light up. Have a ping running from...

May need rout pattern in SM pointing to CM for all extension ranges. When CMM or AAM sends SIP Notify to SM, SM needs the rout pattern to forward MWI to CM. Or is your integration direct with CM?

^ Or Pattern 0 Min 10 Max 10 Insert 9 for the 0123456789 example, not 11

Hi, I checked the 11x0 SIP admin doc and cant see a redial prefix, unlike with the 96xx phones on Aura. In Session Manager you could create and Adaptation that inserts your ARS code for dial back calls. So if your 11x0 dials 0123456789 in SM create a Adaption that matches 0 Min 11 max 11 Insert...

No they probably don't support LLDP, they are old. You can have Avaya SIP B179 on CS1K, but you need to enable SIP LINE on the Node and have SIP LINE licenses.

Not touched one for years, but don't you just boot the 2033, wait for NORTEL or AVAYA on the screen then press the 3 buttons under the screen from left to right??

Try turning off Media Security (MSEC) in LD 17 > PARM Print out first in LD 22. I have seen similar issue with this before. LD 17 CHG PARM .. .. MSEC OFF

Looks like you may have SMTP authentication and or SSL enabled. Check from > Call Pilot Manager "Messaging" - "Message Delivery Configuration" - "SMTP/VPIM" - "Security Modes for SMTP" - Ensure the top 3 SSL tick boxes are unticked and that Unauthenticated is ticked below. #This will only...

Print out VAS in LD 22, as per below. Make sure SECU is YES for both ELAN/VAS or you wont get voice prompts working. > ld 22 PT2000 REQ prt TYPE vas VAS VSID 016 DLOP ELAN 016 SECU YES INTL 0001 MCNT 9999 VSID 032 DLOP ELAN 032 SECU YES...

Make sure Windows Time Service on the CCMS is stopped and set to disabled. An AML CCMS will get its time from the CS1K.

You will need to check in your Sig Server first. SSH CLI to Sig Server and enter : ntpconfig Enter ntp server details as appropriate, then go into CS1K: LD 117 STAT NTP & PRT NTP You should be pointing in LD 117 to your Sig Server that the NTP has been configured. If it is not...

Put DCH monitor on the Virtual Trunks DCH and see what number comes in over SIP. Make sure your digit length on the Audiocodes is set high enough to take the call your dialing, as the default out of the box is 3.

Do you mean S1 Port No ? If so SRG = 7300, CS1K = 4100, BCM = 7000.

Yes in the UK we use LD 49 > FCR tables. These are allow and deny tables, normally use from 1 to 7. 1 is internal only and 7 is unrestricted. 2 - 6 progressively get less restricted. Makes it easy to manage restrictions, but i guess your in US.

Have a look at LD 49 > PRT > FCR Each CRNO No. should associate with the NCOS No. There should be allow and deny tables. Have a look at what digits are allow and deny to see if that ties in with what you can dial on each NCOS. Also do you have CLS = TLD on the phone sets also, you need that...

Are you sure the hard disk you are using is ok. I think they are normally 40GB SeaGate IDE type, they have the copper pins sticking out and you plug that into the IDE connector which is on the card and screw 4 screws into the corners. As your error suggests the hard disk is not not working...

Upto 16 digits max. You will need to enter access code before number e.g. 907711223344

Do you have the DIP switch on the CPPM card set to HD not CF ? I take you have the hard disk installed on the card also ?