Search results for query: *

Talk to your sales rep - you maybe able to get a 90 day demo of the software We upgraded 13 IPXs to r24- found the MA40OO very helpful when we added all 10 sites to an existing FCCS network. using clipboard to load ALGSN,AFRSL, ETC... We use it eveyday for Adds and moves We snyc pbxs eveyday-...

Hi 3racefan i was able to find out the same information - tomorrow ill finish this off and get moving Loaded up a few soft phones and so far so good no sound quality Thanks for all the help

Just to add the PBX information 2400 IPX R24 We are using ITR16-D PHONES The scope is sent by the device the Network will know where to send that device based on thew DHCP scope http://www.networksorcery.com/enp/protocol/bootp/options.htm DHCP options have the same format as the BOOTP...

The phones work when its plugged into the hub card in the pbx - Using the steps you have outlined But these would be both on the same network . I was hoping the NEC would act like the Cisco phone- where you program in the MAC and features of the phones , then plug the phone into a network with...

we have an issue with getting dterm ip to work- WE tested within the PBX (we plug the card and phones in to the hub card inside the PBX- things work fine ) But does anyone know if there is an option code of the phone, We have Cisco phones that have an option code 150 for example that so when...

Not sure if i understand your question – Are you trying to not reuse these extensions when adding phones? for example we excluded certain extensions ranges so a tech can not add them – under feature commands you can assign excluded numbers NEC does offer free training –on the MA4000 go to...

The 2400s are supported but some of the old hardware and software will not be. IMX is no longer supported IPX is fine - Depending on the CP rev you will have to upgrade for any IP phones. We just upgraded 20 NECs to R24 and to upgrade cards with new Chips, replace the old CPUS

What type of NEC pbx is this 2000 or 2400

“But when I changed it to wink,I can see the card wink start the trunk “ You will not see the DTR flash after the wink- the incoming register should take care of the rest Are calls now coming in ?/

Strange it works using immediate start and DP on inbound. you would think if it wink on the outbound it would be wink in bound. Immediate start and dial pulse just sounds wrong If you can perhaps use a fluke or a T-bird and monitor an incoming call - Here are some switch settings i have used...

The 2400 supports both DTMF(Touch Tone) and DP on inbound calls - ARTD CDN 4 set to 3 that would be the standard setting for DP/PB I could not imagine many carriers using dial pulse or a t-1 –

Not sure if this would work -it may stop number dislay for station to station calls ASFC 179 Calling Station Number Display Elimination for Calling Station (North America only) 180 Calling Station Number Display Elimination for Called Station (North America only)

On the outbound PRI see if there is anything in ACBC .The out bound carrier maybe looking for a TAG before letting the call go out, If this is the case you will be SOL \I had a similar issue for years and NEC never figured it out, I ended up adding a NONPRI for this type of application

You maybe better off having the user contact the 800 carrier m they should be able to block the calls. Depending on the carrier there are some routing tools available that a user could route calls by incoming number

Normally you will find the products will work fine on their own. They can run for many years. The issues will come up when you start playing around and cause your own outage. Always backup the systems after programming at least a weekly backup an format. Make sure your UPS is up and running...

Not that i can think of with out access codes,,, Maybe take the card to another site where you can record

I think Connect tape recorder to DAT Turn on MBRQ to make busy the channel to record Turn WR key up Turn START key up Start recorder Return START , WR keys to down when done

Ok pardon me if I ask a few dumb questions The Lens is 011031 So your card should be in PIM1 slot 5 Check to make sure there is nothing else programmed in lens 011020-011037 like tec 18s etc. I would try to add a tec 12 in 011020 that should be the first port on the card. Try turning...

Make sure the toggle switch is down , Only switch to watch for is SW01 POS 7 IF USING IN 16 ELC MODE HAVE IT ON Normally 1-7 are on 8 is not used What slot is your card and and waht LENS did you program the phone in

ADAI Is the command