Search results for query: *

Hey NortelNate 5.5V 1F CAPACITOR 36000 = R.S. part # You will need 2 for the sleeve, and yes you will need to sodier but its an easy one !

Im hoping to save programming and PRI keycode. Here is what i have and what im going to try to do- MICS 4.1xc with RAM V.1 : lots of programming+PRI Key I have a 6.1xc and a RAM V.2- 1) Can i power down, put V2 RAM in with 4.1, power up 2) Power down, put 6.1 in , power up Will i keep...

Thanks Dewey

Trying to load VM Keycode with 9 * 8. After showing VM client, at the Data part, do i enter it 24 dig. or seperate the the 3 sets of 8. Reason for me to try this is, im having trouble in Element Manager loading it from a folder and even manualy with the dashes. The BCM is a 200 with 3.0 sftw...

I'll have to check the appear/ring's on all the sets. Good tips and ill post back, when i go back to site. Thanks

yes, just reception phone to ring more than 4 then to general delivery, hoping for 6.

I can seem to change number of rings higher than 4. Prime set is set under Term/ Set CFNA to VM DN, and put rings at 6. Under Sys Prog Feature settings changed to Call Back Trans to 6 rings. DRT to prime Y. DRT Delay 10. What else could i be missing to make calls ring longer before going to...

Hi Merlinman, Im using CKE 5, which i upgraded to v4. Whats your insite??

Im using the terminal onsite and my laptop for this. I think i figured the problem. I need to add a processor to the second cab. There isnt any ports left for the data mod. Thanks for replying!

Im getting error codes 1, 8 , 11 , 16

Thankyou Main problem is saying out of servive NE,,near end.

Hi Techs, If there was never a DS1 present in the switch, does the tone clock have to changed from a TN2182c to a TN768? The processor is a TN2404 which i believe is a V9si. Is there some sort of a conflict? I know a DS1 TN464f has to be on rel.8.4 or higher. I may be wrong. Any advice will be...

Mr.Telecom your right that was my error it is the 016TR, that was my error. I guesss it applies to firmware 22 or 27, im not completely sure. Is there a patch for the 016 TR? Im running 4.0 on my lab switch is the upgrade sent through the GA rel.4 or is it a special dedicated patch that i would...

Hello Techs, Hopefully someone knows what im talking about. 016 ETR card that runs on Magix- Rumor has it that there is an upgrade for the sleepy port issue. Does anyone know and have any feedback on this. Thanx in Advance!!

Has anyone seen any out of box failures with 4610SWIP's. Two weeks ago 9 out of 20 bad. Yesterday 8 out of 16 bad. All similar issues with handset jack/hookswitch not responding. Definitely not Handset; works in headset jack fine. I noticed all SN# start with 07N532xxxxxx. Any feedback greatly...

Thanks Hawks, At least i wasnt the only one,,, I kept getting the response " are you sure thats the right serial number?" And I have done enough mailbox upgrades that i know i wasnt crazy. Nortel better find out whats up,,, this was the third one.. Thanks again for response!!

I have seen brand new out of the box 7316e's that had displays that were not properly seated inside tight enough. I was able to tell by pressing the bottom middle of where the LCD meets the housing plastic. Plug the phone in and on startup all the arrows should blink if you press where i said...

Has anyone seen over the last couple of weeks CP100 that when trying to get keycodes for upgrades that the SN # are comming up invalid. Im on my third brand new CP100 with same senerio date codes are Sept. 21, 2007??? Is this my bad luck or does someone know something about this? My vendor is...

Hi Hawks thanks for the reply. I did try with four phones and could only get through with one set. I know CP's sometimes crap out from powerhits, but its on a surge/ups and has been ok for the last 6 months. The port lights are all on the 150. Still trying to figure something before the last...

Im very stumped on this CP150 that has three out of the four ports busy. I have made sure ..and tried.. 1. no ext. accessing VM 2. idle in maint 3. disabled/enabled 4. cold reset 5. powercord reset 6. All connections are good What else can i try to free up the other three ports? I havent seen...