Search results for query: *

Hi Bizounett, It's quite easy!Just plug the 2 cables from switch into the the routed interface of the Cisco 2621XM and configure the 2 subnets on the relevant interface. Best regards

Good way to go! So it does work!!Hands up for Cisco they do know their stuff.

Hi Imbadatthis , That's old school stuff,totally forgotten about that one.Too much time away from the access network stuff :-)Yes that should work!! Regards

Hello The problem with the access-list is that your return traffic is getting block because you don't have those high order ports open,that the browser is using. To work around this you should use CBAC or something of the like...

Hello, At work we had the same conf for a client.The only difference is that we used the same access list.Can't guarantee you that it ever work properly becauseI never really got the chance to test the conf fully.All I can say is that the customer ask for a redesign a few weeks ago,maybe for...

Hello Can you please post your present conf.Below is the conf to help you receive inbound calls and make outbound calls with the analog phone. Conf for FXO port : Voice-port x/x/x Signal loopstart Dial-type dtmf Cptone US = your country Connection plar opx 101 = number of choice Caller-id...

Hello, Not all hope is lost. Cisco NBAR is you friend.If you need help with the conf,just post back. Regards

Hello First you will have to see if you have layer 2 connectivity,apply the below commands to the conf of the router and the do a "show isdn status" if you see "State = MULTIPLE_FRAME_ESTABLISHED" you are good to go and then I can help you with the dial-peer settings. interface BRIx/x/x...

Hello, I could be wrong,but I think you are loking in the wrong direction.The the confreg thing is normally use for password recovery,never really seen it use for anything else. The router will boot from nvram if the confreg is set to the default 0x2102.You would set the confreg to ignore...

Hi All the commands should work accept some of the spannng-tree commands.Try again and post the pieces that are giving you problems. Regards

Hello I don't use SDM or CPP,so I don't know for sure.But with CMD it's not difficult. Regards

Sure with Time-Based Access Lists.If it not clear the docs like me know. http://ciscosystems.com/en/US/docs/ios/12_0t/12_0t1/feature/guide/timerang.html Regards

Hello Can you be a bit clearer,why do you want to use DHCP on your WAN.Is this a lab setup or a production network? Normally you would have a subnet /30 on the WAN and a bigger subnet on your LAN /24,here's where you would configure the DHCP pool.In any case the four port switch was design...

Hello Burt has replied to your last post.I did revised the conf I sent you and have notice that you are doing "NAT" so you will have to put the policy-map on the outbound side of the ATM interface: interface atm0 service-policy output SLOWDOWN Good luck

Hello Thanks guys for the replied.Vince the customer wouldn't accept this as a solution,he just needs his bandwith without any tweaking. ISPking ,sorry for the lack of info,our edge router is a 6509 with a pretty recent supervisor,it's doing MPLS VPN for interconnection between customer...

Hello The (CAR) rate-limit command is the old way of doing if your router don't fully support the new way,you will have to upgrade your IOS or use CAR with an access-list.Below is an example of using the Modular QoS CLI (MQC) which is more flexible. access-list 101 permit ip 192.168.1.x...

Hello All We have an issue with a customer that has purchased a 100Mbps link (guaranteed) to the Internet.This customer then resells Internet services to his clients.He's complaining that when the link has low usage he can download at 30Mbps from our test server.But in the busy moments of...

Hello Networking is very flexible,with lots of ways to make things work.Take a shot at it,and if it doesn't work get back to us. Regards

Do you mean when you create a subiterface on the interface Ethernet0/0 ? Regards

Hi Try posting in the voice forum.No voice experts here :-( Regards