Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chris Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

connection E1 between X8 and Eco server 4000 V10

Status
Not open for further replies.
Karmozdi

Karmozdi

Technical User
Feb 18, 2019
124
US
Hi everybody
I have a question about the E1 connection between Ecoserver 4000 V10 and X8.
the call from 4000 to X8 are Ok but It is not possible from X8 to 4000.
with EQMA & ETSI protocols.
Please guide me, what kind of Protocol should I put?
Thanks a lot
----------------------------
ADD-TDCSU:OPT=NEW,PEN=1-01-012-0,COTNO=5,COPNO=5,DPLN=0,ITR=0,COS=5,LCOSV=1,LCOSD=1,CCT=" ",DESTNO=0,PROTVAR="ETSI",SEGMENT=8,DEDSVC=NONE,TRTBL=GDTR,SIDANI=N,ATNTYP=TIE,CBMATTR=NONE,TCHARG=N,SUPPRESS=0,TRACOUNT=10,SATCOUNT=MANY,ALARMNO=0,FIDX=1,CARRIER=1,ZONE=EMPTY,COTX=5,FWDX=5,CHIMAP=N,UUSCCX=16,UUSCCY=8,FNIDX=1,NWMUXTIM=10,CLASSMRK=EC&G711&G729AOPT,TGRP=5,SRCHMODE=CIR,INS=Y,SECLEVEL=TRADITIO,HMUSIC=0,CALLTIM=60,WARNTIM=60,DEV=S2CONN,BCHAN=1&&5,BCNEG=N,BCGR=1,LWPAR=2,LWPP=0,LWLT=0,LWPS=0,LWR1=0,LWR2=0;
----------------------------
CHANGE-LWPAR:TYPE=DIUS2,BLNO=2,LNTYPE=COPPER,VERSION=S2,QUAL=ON,MASTER=Y,DCHAN1=16,DCHAN2=0,PATTERN=D5,QUAL1=10,QUAL2=10,SMD=N,PERMACT=Y,FCBAB=DF,CDG=N,FIXEDTEI=0,CNTRNR=255,TEIVERIF=N,CRC4REP=N,DEV=INDEP;
--------
 
 https://files.engineering.com/getfile.aspx?folder=fcd712cb-f423-47a4-a2e7-814bf2752cf0&file=Screenshot_(1037).png
Sort by date Sort by votes
IF the calls are working from 4K to X8. then the trunk and channels must be up.
THerefore it is not a protocol issue.

If the X8 definitely routing the calls correctly?
My gut instinct would be routing issue, either the incorrect digits are being received or the calls are not going via the correct trunk.
What traces / logs do you have?
 
Upvote 0 Downvote
hi dear Thepfy
I disabled the LCR tick.
I defined the access code, I get a number from X8, the LED of the E1 card flashes on both devices, but 4000 does not ring. show busy on the X8 phone.
Do I have to define DID in 4000?
Please tell me how I should do this.
best regards
--------------------
this is X8 trace log

Nr: Time: Callnumber/Access: State: Event:
152 15:15:40 7801 DIUN2 10-1 Idle
151 15:15:39 7801 DIUN2 10-1 Disconnect Indication Release
150 15:15:39 7801 DIUN2 10-1 DISCONNECT_REQUEST RELEASE COMPLETE (ISDN)
149 15:15:39 7801 DIUN2 10-1 DISCONNECT_REQUEST RELEASE (ISDN)
148 15:15:38 7801 DIUN2 10-1 Disconnect Indication
147 15:15:38 7801 DIUN2 10-1 Call Request Disconnect
146 15:15:38 7801 DIUN2 10-1 OUTGOING_CALL_PROCEEDING DISCONNECT (ISDN)
145 15:15:38 500 SLMO8N 1-1 Idle Monitor Off
144 15:15:38 500 SLMO8N 1-1 Idle
143 15:15:38 500 SLMO8N 1-1 Disconnect Indication
142 15:15:38 500 SLMO8N 1-1 Busy On Hook
141 15:15:31 500 SLMO8N 1-1 Busy Off Hook
140 15:15:29 500 SLMO8N 1-1 Busy
139 15:15:29 7801 DIUN2 10-1 Call Request Progress
138 15:15:29 7801 DIUN2 10-1 OUTGOING_CALL_PROCEEDING CONTINUATION
137 15:15:29 7801 DIUN2 10-1 OUTGOING_CALL_PROCEEDING PROGRESS (ISDN)
136 15:15:29 Unknown State (255) SEGMENT (ISDN)
135 15:15:29 Unknown State (255) CONTINUATION
134 15:15:29 Unknown State (255) SEGMENT (ISDN)
133 15:15:29 500 SLMO8N 1-1 Outgoing Call Proc
132 15:15:29 7801 DIUN2 10-1 Call Request Call Proc
131 15:15:29 7801 DIUN2 10-1 OVERLAP_SENDING CALL PROC. (ISDN)
130 15:15:29 7801 DIUN2 10-1 OVERLAP_SENDING INFORMATION (ISDN)
129 15:15:29 7801 DIUN2 10-1 Call Request Info
128 15:15:29 500 SLMO8N 1-1 Overlap Sending Digit
127 15:15:29 7801 DIUN2 10-1 OVERLAP_SENDING INFORMATION (ISDN)
126 15:15:29 7801 DIUN2 10-1 Call Request Info
125 15:15:29 500 SLMO8N 1-1 Overlap Sending Digit
124 15:15:28 7801 DIUN2 10-1 OVERLAP_SENDING INFORMATION (ISDN)
123 15:15:28 7801 DIUN2 10-1 Call Request Info
122 15:15:28 500 SLMO8N 1-1 Overlap Sending Digit
121 15:15:28 7801 DIUN2 10-1 CALL_INITIATED SETUP ACK. (ISDN)
120 15:15:28 7801 DIUN2 10-1 Call Request Info
119 15:15:28 7801 DIUN2 10-1 CALL_INITIATED SETUP (ISDN)
118 15:15:28 500 SLMO8N 1-1 Overlap Sending Digit
117 15:15:26 7801 DIUN2 10-1 Call Request Setup Ackn
116 15:15:26 7801 DIUN2 10-1 Call Request
115 15:15:26 7801 DIUN2 10-1 Idle Setup
114 15:15:26 500 SLMO8N 1-1 Overlap Sending Monitor On
 
Upvote 0 Downvote
hello everybody
please help me about this problem .thank you for your advance .
how shall I setting incoming call in 4000 v10.
I don't have any problem incoming call in Hipath 4000 V7 .I only have this problem in Openscape 4000
best regards
 
Upvote 0 Downvote
The Extensions that are on the X8 have to be added to the V10
A route (CD RICHT) should be setup to allow dialling from the V10 to the X8
 
Upvote 0 Downvote
Hi Dear sbcsu
thank you for your answer My question.
call from V10 to X8 are Ok but from X8 to 4000 not ok.
License,LCR,Date,and setting in X8 are ok .V10 License is on Grace period too.
thanks a lot
 
Upvote 0 Downvote
The RDS trace from the 4K would be more use here, because it would show exactly what digits the 4K has received. You could try that but I think on V10 R0 RDS had problems, it might not work properly.
Looks like you get a CALL PROC but there is no ALERT. 4K thinks it has enough digits to start processing but then can't, it finds nothing it can ring with the digits it has.

Either you are sending the wrong digits from OSBiz, or you send the correct digits but you have not added them properly in WABE on the 4K.

Protvar "ETSI" is a strange choice for networking to X8, I would have expected ECMAV2 segment 8, i.e full QSIG both sides. But ETSI will work, at least I would not expect it to cause this problem you have now.
 
Upvote 0 Downvote
By default, for a CO-call, OSBiz sends the trunk code
to the line (echoall - E1A). There may be a problem here.
 
Upvote 0 Downvote

Hello Dear Moriendi .nice to meet you .this is my rout setting .only i have problem call from X8 to 4000 .When I dial 4000 from x8, both DIUN2 cards flash, but the phone does not ring on 4000.
ADD-BUEND:TGRP=5,NAME="PRI-X8 ",NO=5,TRACENO=2,ACDTHRH=*,PRIONO=1,TDDRFLAG=ON,GDTRRULE=0,ACDPMGRP=0,CHARCON=NEUTRAL;
ADD-TDCSU:OPT=NEW,PEN=1-01-012-0,COTNO=120,COPNO=120,DPLN=0,ITR=0,COS=5,LCOSV=1,LCOSD=1,CCT=" ",DESTNO=0,PROTVAR="ECMAV2",SEGMENT=8,DEDSVC=NONE,TRTBL=GDTR,SIDANI=N,ATNTYP=TIE,CBMATTR=NONE,TCHARG=N,SUPPRESS=0,DGTPR=4000,TRACOUNT=10,SATCOUNT=MANY,ALARMNO=0,FIDX=1,CARRIER=1,ZONE=EMPTY,COTX=120,FWDX=5,CHIMAP=N,UUSCCX=16,UUSCCY=8,FNIDX=1,NWMUXTIM=10,CLASSMRK=EC&G711&G729AOPT,TGRP=5,SRCHMODE=CIR,INS=Y,SECLEVEL=TRADITIO,HMUSIC=0,CALLTIM=60,WARNTIM=60,DEV=S2CONN,BCHAN=1&&5,BCNEG=N,BCGR=1,LWPAR=2,LWPP=0,LWLT=0,LWPS=0,LWR1=0,LWR2=0;
CHANGE-LWPAR:TYPE=DIUS2,BLNO=2,LNTYPE=COPPER,VERSION=S2,QUAL=ON,MASTER=N,DCHAN1=16,DCHAN2=0,PATTERN=D5,QUAL1=10,QUAL2=10,SMD=N,PERMACT=Y,FCBAB=DF,CDG=N,FIXEDTEI=0,CNTRNR=255,TEIVERIF=N,CRC4REP=N,DEV=INDEP;
ADD-RICHT:MODE=LRTENEW,LRTE=5,LSVC=ALL,TGRP=5,DNNO=1-1-100,ROUTOPT=NO,ROUTATT=NO,EMCYRTT=NO,PDNNO=0,CONFTONE=NO,RERINGRP=NO,NOPRCFWD=NO,NITO=NO,CLNAMEDL=NO,FWDSWTCH=NO,LINFEMER=NO,NOINTRTE=NO;
ADD-COP:COPNO=5,PAR=L3AR&LKNQ&PRMT;
CHANGE-COP:COPNO=5,COPTYPE=COPADD,DEV=S2CONN;
ADD-COT:COTNO=5,PAR=PRI&RCL&XFER&KNOR&CEBC&CBBN&CBFN&IEVT&BSHT&BLOC&PROV&ATRS&TS
CS&TRSC&CFOS&PINR&AOCC&CTLS&AMFC&NTON;
CHANGE-COT:COTNO=5,COTTYPE=COTADD,DEV=S2COD,INFO="20: S0/2 AMT EDSBRD O. ABWURF"
;
ADD-LODR:ODR=5,CMD=ECHO,FIELD=2;
ADD-LODR:ODR=5,CMD=END;
ADD-LDAT:LROUTE=5,LSVC=ALL,LVAL=1,TGRP=5,ODR=5,LAUTH=1,CARRIER=1,ZONE=EMPTY,LATT
R=NONE,VCCYC=4;
ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP="*8"-"X",DPLN=0&1&2&3&4&5&6&7&8&9&10&11&
12&13&14&15,LROUTE=5,LAUTH=1,PINDP=N;
ADD-WABE:CD=4000&&4005,DAR=STN,CHECK=N;
ADD-WABE:CD=*8,DAR=TIE,CHECK=N;
ADD-WABE:CD=*9,DAR=TIE,CHECK=N;
DIS-SDSU:ALL,,PEN,PER3,1,1,12,0;
H500: AMO SDSU STARTED

LTG1 (PERIPHERY)
------
MOUNTING LOCATION MODULE NAME BDL BD(#=ACT) STATUS
------------------- LTG 1 --------------------- READY
-AP370013-----SG 1 LTU 1 --------------------- READY
** .LTG 1.LTU 1.012 DIU-N2 Q2196-X READY
CCT LINE STNO SI BUS TYPE
000 1486 PP NW READY
MULTLINE 30 . . . . . . . . . . . . . .READY
000 NO CONN
001 NETWORK SUBUNIT . TMD CONN ISDN READY
(ALT_ROUT: N) (S2CONN )
STN NO in 4K= 4000
STN NO IN X8= 1000
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
setting in OSBIS X8 :
Master
PRI Ecma Qsig master
;;;;;;;;;;;;;;;;;
pleas help me
thank you for your advance
best regards


 
Upvote 0 Downvote
Hello dear Masviss
I defined the LCR as E2A in X8,Contact with all Siemens devices is established:
I have this problem with the 4K V10
E1 4k v7 with Hipath 3800 calls are Ok
E1 4k v7 with Hipath 3550 calls are Ok
E1 4k v7 with Hipath X8 calls are Ok
E1 4k v10 with Hipath X8 calls are Not Ok. only call from 4k V10 to X8 is Ok
 
Upvote 0 Downvote
all of system 3550, 3800 and X8 systems with 4K V10 have this problem as well.
Only connection is established from the 4k v10 side
 
Upvote 0 Downvote
In your original ADD-TDCSU line you have no digit prefix (DGTPR). In the 2nd one, you have a DGTPR of 4000. Is that right? You want to prefix all calls with 4000? And you have a WABE added for STN 4000 but is it added?

Like I said, you are not sending digits to the 4K that it can use, and don't forget you are now putting 4000 on the front of every incoming call, which does not sound right.

There is no V10 problem here. There is an Asghar configuration problem.
 
Upvote 0 Downvote
Is the phone 4000 plugged into the port?
Please show
DIS-SDSU:ALL,,STNO,PER3,4000;
The dial the number on OSBiz and show
DIS-SDSU:ALL,,STNO,PER3,4000;
without handset down on OSBiz.
How many subscriber numbers
have you programmed for OS4K?
4000&&4999?
 
Upvote 0 Downvote
Dear Masviss
Because it was not possible to call 4k subscribers,
I set the DGTPR trunk destination to test 4000, but the 4000 phone does not ring.
 
Upvote 0 Downvote

DIS-SDSU:ALL,,STNO,PER3,4000;
H500: AMO SDSU STARTED

STATION NUMBER ACCORDING TO PORT EQUIPMENT NUMBER
-------------------------------------------------
MOUNTING LOCATION MODULE NAME BDL BD(#=ACT) STATUS
** .LTG 1.LTU 1.001 SLMO24 ? Q2168-X READY
STNO INPUT CCT LINE STNO SI BUS TYPE
4000 000 1454 OPTI ONLY READY
MULTLINE 8. . . . . . . . . . . . . . .READY
001 SUBUNIT . . . . . DIGITE MAIN READY
(ALT_ROUT: N) (OPTIP500)
LINE: 1491 STNO: 4000 SI:VCE
001 . . . . . . . . DIGITE SUB A READY
002 . . . . . . . . DIGITE SUB A READY
003 . . . . . . . . DIGITE SUB C READY
............................................................
I have two station User know for test
<reg-sbcsu;
REG-SBCSU;
H500: AMO SBCSU STARTED
ADD-SBCSU:STNO=200,OPT=OPTI,CONN=DIR,PEN=1-1-1-1,DVCFIG=OPTIP500,TSI=1,COS1=1,CO
S2=1,LCOSV1=1,LCOSV2=1,LCOSD1=1,LCOSD2=1,DPLN=0,ITR=0,SSTNO=N,COSX=0,SPDI=0,SPDC
1=0,IDCR=N,REP=0,STD=12,SECR=N,INS=Y,ALARMNO=0,RCBKB=N,RCBKNA=N,DSSTNA=N,DSSTNB=
Y,DIGNODIS=N,CBKBMAX=5,HEADSET=N,HSKEY=NORMAL,CBKNAMB=Y,TEXTSEL=ENGLISH,HMUSIC=0
,CALLOG=ALL,COMGRP=0;
ADD-SBCSU:STNO=4000,OPT=OPTI,CONN=DIR,PEN=1-1-1-0,DVCFIG=OPTIP500,TSI=1,COS1=1,C
OS2=1,LCOSV1=1,LCOSV2=1,LCOSD1=1,LCOSD2=1,DPLN=0,ITR=0,SSTNO=N,COSX=0,SPDI=0,SPD
C1=0,IDCR=N,REP=0,STD=12,SECR=N,INS=Y,ALARMNO=0,RCBKB=N,RCBKNA=N,DSSTNA=N,DSSTNB
=Y,DIGNODIS=N,CBKBMAX=5,HEADSET=N,HSKEY=NORMAL,CBKNAMB=Y,TEXTSEL=ENGLISH,HMUSIC=
0,CALLOG=ALL,COMGRP=0;
...............................................................................
ADD-WABE:CD=200,DAR=STN,CHECK=N;
ADD-WABE:CD=4000&&4005,DAR=STN,CHECK=N;
ADD-WABE:CD=*8,DAR=TIE,CHECK=N;
ADD-WABE:CD=*9,DAR=TIE,CHECK=N;
 
Upvote 0 Downvote
DIS-SDSU:ALL,,PEN,PER3,1,1,12,0;
------
MOUNTING LOCATION MODULE NAME BDL BD(#=ACT) STATUS
------------------- LTG 1 --------------------- READY
-AP370013-----SG 1 LTU 1 --------------------- READY
** .LTG 1.LTU 1.012 DIU-N2 Q2196-X READY
CCT LINE STNO SI BUS TYPE
000 1486 PP NW READY
MULTLINE 30 . . . . . . . . . . . . . .READY
000 NO CONN
001 NETWORK SUBUNIT . TMD CONN ISDN READY
(ALT_ROUT: N) (S2CONN )
LINE: 1486 STNO: SI:
001 . . . . . . . . TMD CONN ISDN READY

 
 https://files.engineering.com/getfile.aspx?folder=b5599eb6-0827-4c41-9803-f98dc81054b0&file=Screenshot_(1071).png
Upvote 0 Downvote
I have a question, please help me.
For communication between users of devices
4K V10 with X8 should be in my 4k DID or node number (KNDEF)
Describe ?
thanks a lot
 
Upvote 0 Downvote
Kndef is usually configured but doesn’t have to be. If this is your problem depends on what digits are coming in.

V10 is always tracing. You can download the files from Assistant, expert mode, permanent logging. Post a trace.
 
Upvote 0 Downvote
Please guide me from which of the following options to report?

System status AMO SIGNL 2023-10-26 14:40:01
System Version APS/Sysinfo 2023-10-26 14:40:01
RMX memory allocations AMO DIMSU 2023-10-26 14:40:01
RMX statistics AMO ZAUSL 2023-10-26 14:40:01
RMX DIAG partition DIAG partition usage info 2023-10-26 14:40:01
Error message overview AMOs HISTA/VADSU/VADSM 2023-10-26 14:40:01
AUTO trace CC-A (simplex) 2023-10-26 14:40:01
Inventory Data HIM/PB file info & GWM board list 2023-10-26 14:40:01
REGEN Last REGEN ALL file creation date not available
Download all (incl. LOGBK, ADP and CC logs)
 
 https://files.engineering.com/getfile.aspx?folder=b60e77c4-25fe-4a7b-987b-5d2c327b6d11&file=AUTO_TRACE_2023-10-26_144001_info.log
Upvote 0 Downvote
Status
Not open for further replies.

Similar threads

iiaacc
  • Locked
  • Question
Openscape 4000 v10 standby ecoserver can't boot 2
Replies
6
Views
916
Moriendi
Moriendi
Y
  • Question
Hotfix for OS 4000 V10 R0 28
Replies
6
Views
345
yosi4enko
Y
ashraf55
  • Question
import xml file from existing running eco server
Replies
1
Views
237
Moriendi
Moriendi
ashraf55
  • Locked
  • Question
enterprisegateway v10
Replies
10
Views
350
ashraf55
ashraf55
Karmozdi
  • Locked
  • Question
Setting Incoming call link E1 to 4000 V10
Replies
0
Views
126
Karmozdi
Karmozdi

Part and Inventory Search

Sponsor

Back
Top