connection E1 between X8 and Eco server 4000 V10

[Karmozdi]

Hi everybody
I have a question about the E1 connection between Ecoserver 4000 V10 and X8.
the call from 4000 to X8 are Ok but It is not possible from X8 to 4000.
with EQMA & ETSI protocols.
Please guide me, what kind of Protocol should I put?
Thanks a lot
----------------------------
ADD-TDCSU:OPT=NEW,PEN=1-01-012-0,COTNO=5,COPNO=5,DPLN=0,ITR=0,COS=5,LCOSV=1,LCOSD=1,CCT=" ",DESTNO=0,PROTVAR="ETSI",SEGMENT=8,DEDSVC=NONE,TRTBL=GDTR,SIDANI=N,ATNTYP=TIE,CBMATTR=NONE,TCHARG=N,SUPPRESS=0,TRACOUNT=10,SATCOUNT=MANY,ALARMNO=0,FIDX=1,CARRIER=1,ZONE=EMPTY,COTX=5,FWDX=5,CHIMAP=N,UUSCCX=16,UUSCCY=8,FNIDX=1,NWMUXTIM=10,CLASSMRK=EC&G711&G729AOPT,TGRP=5,SRCHMODE=CIR,INS=Y,SECLEVEL=TRADITIO,HMUSIC=0,CALLTIM=60,WARNTIM=60,DEV=S2CONN,BCHAN=1&&5,BCNEG=N,BCGR=1,LWPAR=2,LWPP=0,LWLT=0,LWPS=0,LWR1=0,LWR2=0;
----------------------------
CHANGE-LWPAR:TYPE=DIUS2,BLNO=2,LNTYPE=COPPER,VERSION=S2,QUAL=ON,MASTER=Y,DCHAN1=16,DCHAN2=0,PATTERN=D5,QUAL1=10,QUAL2=10,SMD=N,PERMACT=Y,FCBAB=DF,CDG=N,FIXEDTEI=0,CNTRNR=255,TEIVERIF=N,CRC4REP=N,DEV=INDEP;
--------

 

[masviss]

For X8

For OS4k

CHA-TDCSUEN=1-1-12-0,PROTVAR=CORNV33,SEGMENT=1,DEV=S2CONN,BCGR=1;

 

[Karmozdi]

I did according to your instructions, but the signaling is not established

<DIS-SDSU:ALL,,PEN,PER2,1,1,12,0;
DIS-SDSU:ALL,,PEN,PER2,1,1,12,0;
H500: AMO SDSU STARTED

LTG1 (PERIPHERY)
------
MOUNTING LOCATION MODULE NAME BDL BD(#=ACT) STATUS
------------------- LTG 1 --------------------- READY
-AP370013-----SG 1 LTU 1 --------------------- READY
** .LTG 1.LTU 1.012 DIU-N2 Q2196-X READY
CCT LINE STNO SI BUS TYPE
000 1486 PP NW DEPLOCK/NPR

 

[masviss]

REST-BSSUEN,1,1,12;

wait 15-20sec

I do not know how DIUT2 will work.
I have not tested this protocol on OS4k V10.

PRI QSIG - ECMA this is the most correct connection option.

Back to the ECMAV2 protocol

CHA-TDCSUEN=1-1-12-0,PROTVAR=ECMAV2,SEGMENT=8,DEV=S2CONN,BCGR=1;

 

[Karmozdi]

I replaced the Cornetnv33 protocol with all OSBIS protocols. He did not answer again.

 

[masviss]

I am so sorry. All claims to ATOS.

 

[masviss]

This is an variant for testing.

 

[Karmozdi]

Hello, dear Masviss
Thank you in advance for your support
EQMAV1 protocol I put it too, but it didn't work.
According to your instructions, replace the OSBIS card with DIUT2X100 and the OS4K card with DIUT2 X200 instead, it has exactly the same problems as before.

I did everything on this device, not only X8, other devices with 4KV10 have this problem.
You also took a lot of time for me. I was ashamed of you. I really wanted to give you happy news to make up for your tiredness, but unfortunately I

 

[Karmozdi]

but unfortunately I couldn't.

 

[Karmozdi]

Do you think I should reinstall OS4K V10 Operating System?

 

[masviss]

ADD-KNDEF:1-1-XXX,OWN,,,,,EXT,,,,,EXT,,,,,,,;
CHANGE-KNDEF:1-1-XXX,,,,,,,,,,,,,,Y,,,0;

 

[Karmozdi]

Call cannot be established
ADD-KNDEF:NNO=1-1-110,TYPE=OWN,ISDNUL=EXT,PNPUL=EXT,NODETRK=N;
CHANGE-KNDEF:NNO=1-1-110,DFLT=Y;

I have a question, should I change an option after defining KNDEF in ZAND and typing ALLDATA?

CHANGE-ZAND:TYPE=ALLDATA,TRANSFER=EXTEND,ALERTN=NO,AUTHUP=TA,RNGBKTN=YES,TRANSINH=NO,NIGHT=TA,ITRFWD=NO,HOLDTN=MUSIC,ANATESIG=TONE,DSSLT=20,CODTN=YES,CONFSUB=NO,DATEDIS=DDMM,CNTRYCD="0",RCLLT=YES,MELODY="2",CPBLOWL=80,CPBUPPL=100,CUTHRU1A=YES,PREDIA=YES,SIUANN="4",CO=YES,COEXN=0,CBKNO=99,SEVDIG=NO,PNNO=110,DISPMODE=MODE2,PNODECD=1,ROUTOPTP=NO,ROUTOPTD=NO,CALLOFF=YES,PARARING=YES,DSSDEST=NO,ONEPARTY=YES,MSGDELAY=YES,EXCOCO=YES,TRDGTPR=NO,COANN=NO,HOTDIAL=NO,TRANSTOG=YES,NOCFW=NO,HOLDHUNT=NO,POSTDDLY=YES,EXBUSYOV=YES,OVRMST=NO,OVRHUNT=NO,CONITPRO=NO,RECHUNT=NO,CALLACMP=YES;

 

[Karmozdi]

When I put the call destination in DGTPR number 4000, as soon as I pick up number 4 from 3800 or X8, the cards flash and the phone rings busy.
When I don't put the call destination, I don't put 4000, the cards flash, but the phone is silent.

 

[masviss]

ADD-KNDEF:1-1-110,OWN,,,,,EXT,,,,,EXT,,,,,,,;
CHANGE-KNDEF:1-1-110,,,,,,,,,,,,,,Y,,,0;

 

[masviss]

Why there is no call when you dial the whole
number is not clear to me. It's very difficult
to play blind.
To understand the problem, we need a trunk trace
from the OS4K side.

 

[masviss]

Please do this

ADD-COT:15,RCL&ANS&CEBC&TIE&CBBN&CBFN&PROV&LWNC&NLCR&TSCS&DFNN&NTON;
CHA-TDCSUEN=1-1-12-0,COTNO=15;

make a call from OSBiz to OS4k

 

[Karmozdi]

Hello Mr.Masviss
The connection of the device was established. I will tell you the problems as soon as possible.

 

[masviss]

Ok.

 

[Karmozdi]

Hello, dear Masviss
First, I converted the Echo Server device with the other hard drive to version 7.
The communication between the two sides of the device was activated.
Then I activated version 10 on this hard drive. Only with the ETSI protocol and the two sides of the Master,
the communication between the two sides is activated.
Mr. Masviss, the most important point was COSSU, communication with this COSSU was activated.
........................................
ADD-BUEND:TGRP=30,NAME="E1 TO X8 ",NO=30,TRACENO=0,ACDTHRH=*,PRIONO=1,TDDRFLAG=ON,GDTRRULE=0,ACDPMGRP=0,CHARCON=NEUTRAL;
ADD-COP:COPNO=30,TRK=TA,TOLL=TA;
CHANGE-COP:COPNO=30,COPTYPE=COPADD,DEV=S2COD,INFO="20: S0/2 AMT EDSBRD O. ABWURF";
ADD-COT:COTNO=30,PAR=PRI&RCL&ANS&KNOR&CEBC&CBBN&CBFN&FWDN&FNAN&BSHT&ATRS&TSCS&TR
SC&CFVA&LINO&SNBE&IICB&NQPI&NCDR&NOFT&NQNP&NIN2&PGEP&NTON;
CHANGE-COT:COTNO=30,COTTYPE=COTADD,DEV=S2CONN,INFO="34: S0/2 QUER CORNV33 < V3.5";

ADD-COSSU:NEWCOS=1;
CHANGE-COSSU:TYPE=COS,COS=1,AVCE=TA&TNOTCR&CDRATN&CDRS&CDRSTN&CDRC&CDRIND&CDRINT;
CHANGE-COSSU:TYPE=COS,COS=1,AVCE=COSXCD&MB&HOT&CFNR&VCE&FWDNWK&TTT&CFB;
CHANGE-COSSU:TYPE=COS,COS=1,AVCE=FWDFAS&FWDDIR&CFSWF&FWDBAS&FWDECA&FWDEXT&CW&CFKL;
CHANGE-COSSU:TYPE=COS,COS=1,AFAX=NOCO&NOTIE;
CHANGE-COSSU:TYPE=COS,COS=1,ADTE=NOCO&NOTIE;

ADD-TDCSU:OPT=NEW,PEN=1-01-014-0,COTNO=30,COPNO=30,DPLN=0,ITR=0,COS=1,LCOSV=1,LCOSD=1,CCT="E1 TO X8 ",DESTNO=10,PROTVAR="ETSI",SEGMENT=1,DEDSVC=NONE,TRTBL=GDTR,SIDANI=N,ATNTYP=CO,CBMATTR=NONE,TCHARG=N,SUPPRESS=0,ISDNIP=00,ISDNNP=0,PNPAC=3888,TRACOUNT=10,SATCOUNT=MANY,NNO=10,ALARMNO=2,FIDX=1,CARRIER=1,ZONE=EMPTY,COTX=30,FWDX=5,CHIMAP=N,UUSCCX=16,UUSCCY=8,FNIDX=1,NWMUXTIM=10,CLASSMRK=EC&G711&G729AOPT,TGRP=30,SRCHMODE=CIR,INS=Y,SECLEVEL=TRADITIO,HMUSIC=0,CALLTIM=60,WARNTIM=60,DEV=S2COD,BCHAN=1&&30,BCNEG=N,BCGR=1,LWPAR=1,LWPP=0,LWLT=0,LWPS=0,LWR1=0,LWR2=0;
CHANGE-LWPAR:TYPE=DIUS2,BLNO=0,LNTYPE=COPPER,VERSION=S2,QUAL=ON,MASTER=Y,DCHAN1=
16,DCHAN2=0,PATTERN=D5,QUAL1=10,QUAL2=10,SMD=N,PERMACT=Y,FCBAB=DF,CDG=N,FIXEDTEI
=0,CNTRNR=255,TEIVERIF=N,CRC4REP=N,DEV=INDEP;

ADD-RICHT:MODE=LRTENEW,LRTE=30,LSVC=ALL,NAME="PRI X8 ",TGRP=30,DNNO=1-1-
105,ROUTOPT=NO,REROUT=NO,DTMFCNV=FIX,DTMFDISP=DIGITS,DTMFTEXT="DIGITAL TRUNK "
,DTMFPULS=PP300,PLB=NO,ROUTATT=NO,EMCYRTT=NO,PDNNO=0,CHARCON=NEUTRAL,CONFTONE=NO
,RERINGRP=NO,NOPRCFWD=NO,NITO=NO,CLNAMEDL=NO,FWDSWTCH=NO,LINFEMER=NO,NOINTRTE=NO;

ADD-LODR:ODR=30,CMD=ECHO,FIELD=2;
ADD-LODR:ODR=30,CMD=END;

ADD-LDAT:LROUTE=30,LSVC=ALL,LVAL=1,TGRP=30,ODR=30,LAUTH=1,CARRIER=1,ZONE=EMPTY,L
ATTR=NONE,VCCYC=4;

ADD-WABE:CD=7,DAR=TIE,CHECK=N;

ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP="7"-"X",DPLN=0&1&2&3&4&5&6&7&8&9&10&11&1
2&13&14&15,LROUTE=30,LAUTH=1,SPC=7,PINDP=N;

ADD-WABE:CD=4000,DAR=STN,CHECK=N;
ADD-SBCSU:STNO=4000,OPT=OPTI,CONN=DIR,PEN=1-1-1-0,DVCFIG=OPTIP500,TSI=1,COS1=1,C
OS2=1,LCOSV1=1,LCOSV2=1,LCOSD1=1,LCOSD2=1,DPLN=0,ITR=0,SSTNO=N,COSX=0,SPDI=0,SPD
C1=1,IDCR=N,REP=0,STD=12,SECR=Y,INS=Y,ALARMNO=0,RCBKB=N,RCBKNA=N,DSSTNA=N,DSSTNB
=Y,DIGNODIS=N,CBKBMAX=5,HEADSET=N,HSKEY=NORMAL,CBKNAMB=Y,TEXTSEL=ENGLISH,HMUSIC=
0,CALLOG=ALL,COMGRP=0;

CHA-COSSU:LCOSV,1,1;

REG-KNDEF;
H500: AMO KNDEF STARTED
ADD-KNDEF:NNO=1-1-110,TYPE=OWN,ISDNCC=0,ISDNAC=0,ISDNLC=2995,ISDNSK=4,ISDNUL=SUB
,PNPUL=EXT,NODETRK=N;
ADD-KNDEF:NNO=120,TYPE=OWN,ISDNUL=SUB,PNPUL=EXT,NODETRK=N;
CHANGE-KNDEF:NNO=120,DFLT=Y;

............................
Best regards
A.Asghar

 

[Karmozdi]

It should be noted that I did not make any changes in OSBIS because I was sure of its settings

 

[dreb20]

Hi,,

please check attached