Search results for query: *

Hello Barney The 1140 you are having trouble with has almost certainly got SiP firmware on it - sounds like you need it to have the proprietory Nortel UNISTIM firmware for use on the CS1k/BCM platform. Does the firmware filename on the phone look like this (SiP)? 04.01.13.00 The Unistim...

you have two IP devices registered to the system with the same extension number. change the extension number to something else and the device will register ok

the firmware load is currupt - seeing as the phone is not even getting to the point where the network is 'up' (ie DHCP etc) the only solution is to have the phone hardware-repaired. I have done loads of these, the number 1 fault with the 8811/41/51's. Unlike the good old 79xx series there is no...

Hello Alfasud Had a look at the alarms on the attached listings and they suggest you have had some form or power-outage - lots of 'passed' PCM link errors, but, one outstanding type 60. The type 60 error is related to the common input/output bus that handles communication between the active...

Hello all Just got hold of a Cisco NME-CUE module for my home lab setup to have a play around with the voicemail on Callmanager Express. Managed to get the module installed and can now dial into the voicemail - however all of the prompts are in French! Needless to say i would like them to be...

One way of seeing if there is a POT phone hooked up to an extension channel is to change the 'No Test Flag' setting for each of the analogue extension channels. This tells the DX to run a very basic diagnostics test on the extension channel - if no telephone is on the the end of the extension...

Hello sir The DDI info thing is a pain in the posterior on the DX - in my experience the best way of finding out what DDI is mapped to what extension is to go to the carrier service provider of the your iSDN/DASS trunks and obtain the DDI range assignments on a per-circuit basis. Once you have...

Hello You are correct in assuming most handset curly cords are wired the same - i.e pin 1 to 4, 2 to 3, 3 to 2 and 4 to 1 (rollout/rolover). Also, if the telephone does not detect a load on the handset-piece jack (its on the microphone pins 2/3) on the base of the phone when the hookswitch...

Hello chaps By my own admission i don't pertain to be the worlds Guru on the Nortel Meridian/Option 11/Cs1000 product but i do use these fine machines to repair a veritable cornucopia of IP/TDM phones on a day-to-day basis. Therefore i think the gentleman/Lady/Person may be encountering a...

Hello chaps By my own admission i don't pertain to be the worlds Guru on the Nortel Meridian/Option 11/Cs1000 product but i do use these fine machines to repair a veritable cornucopia of IP/TDM phones on a day-to-day basis. Therefore i think the gentleman/Lady/Person may be encountering a...

Hello Tony First of all, what a wonderfully-worded first post, and yes, there are still a few fellas like me on this forum with the knowledge available to help you. I myself am a bit like you but in an opposite sense, loads of knowledge on the TDM side of things but not much on the various...

Power off the router, remove the compact flash and then power on, this router will reboot twice finding no flash card and then boot into Rommon Get yourself a USB compact flash card reader (can get these for around £20 in the UK from Maplin), pop in your flash card and have a look at the...

Hello AmeyUk Should be no problem to do this. log onto to the router that you wish to attach your specific system (new server?) and create a static route pointing to it, then log into the EIGRP AS on the router and use the 'redistribute static' command to distribute the static route to the...

Hello colin Log in to the DX via the V.24 programming port or, if running software 6.0 and above, telnet, and input the following command. LSLT A C list slot all configured This will list off what is configured on each slot/shelf, however please bear in mind it will not show the card part...

Hello Pabx1121 i have just posted a possible solution to this over on the Avaya ip office forum Pablo100

Hello pabx1121 i had this exact same problem, created the config file as you have above in notepad and saved it as .cfg - but, notepad automatically saved it as the following file: 1140e.cfg.txt (in my case i was converting 1140's to SiP for a lab experiment) notepad saved it with a .txt...

hello tech250 it may be a good idea to confirm that the DTU line card that the phone is connected to is running the correct firmware. For Openstage support it should be...... 1SBA50405AAA ENU 08-03 as a minimum wondering how to check? Log into to the system, locate the physical address of...

lots of you guys are asking this, see my post over on the Nortel BCM forym same phone/same firmware/same method http://www.tek-tips.com/viewthread.cfm?qid=1688940

i have just posted this over on the Nortel BCM forum, same phone/same firmware/same procedure. http://www.tek-tips.com/viewthread.cfm?qid=1688940 Let us know how you get on.

Hello and welcome to the forum, i faced a similair situation as yours a few weeks ago. Method as follows. to upgrade an 1140e to the latest unistim firmware 1. place the following '1140e.cfg' text file along with the required firmware downloaded from avaya in your TFTP root directory (i.e...