Search results for query: *

COM 1 is the DTE connection , and if you are getting to the tools menu it must be reading the floppy-----------------do you see the CD LED flicker when you hit the carriage return? try putty ---direct 9600 8 1 none

ld 48 dis elan 32 test

hey monkey----------------------is the route data block for the paging (wat) set up for MANO=yes? you replyed above that the trunk is unr/dtn------------------------------are the qsig trunks also set up as unt/dtn? have you turned on d-ch messaging and verified the cs1k is sending back a...

So you can call from the mitel and make the connection------but then you can not dial the zone---check your trunks between the 2 pbx's. Verify that they are DTN and also UNR on the cs1k side. Once you make the connection to the cs1k's paging trunk the system is looking at the features on the...

the keys start at 0---you started programming them on 1 so reprogram the keys as : 00 SCR 5350 0 01 SCR 6351 0

It's been a long time since this was an issue on the Opt11 but I found my old notes. The system is probably using WCAD 002 for DCAD in table 0. Change the settings for wcad 004- WCAD 4 CDNC 00102 00102 00205 00410 00000 00000 00000 00000 00000 00000-4th field is normally 0819 --this setting...

in element manager under Dialing and Numbering plans---then look for ESN (electronic switched network.) then under the heading customerr 00 -Network Control & Services---Flexible CLID open that and you can view and modify existing---or add new CLID tables

have you tried ESS5 on the IPO?

Nortel/Avaya has never allowed a tandem DID to DID call going back as far as I can remember and NI2 is always DID, unless you have the plug in or back in earlier releases a patch which will let you call the route type tie. NI2 is for central office connections. We have been using qsig on the...

There is a backup on the SSC if you still have it. Install new software on the software db and when you select database during the install choose basic. After the system comes up the 1st time log in with ADMIN2 and pwd=0000 ld 143---UPGRADE pick utilities and then restore from flash

I go into ld 48 and type FLSH

Toll free numbers want to see a valid calling line ID----verify that you are sending a good clid from your tn's on the Call Pilot .

this is a 4.50 system I have and I can get into all the overlays---with the customer blank. Can you get into any overlays?--or just not 117 and 96? USER_NAME TEST TYPE LAPW_OVL OVLA 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020...

I agree with KCFLHRC--------there is no need to configure it as a backup---just call it a member.As a member it will give you backup on your SIP . When adding a server to the domain it is always looking for the TLAN.

this message shows the disconnect from the far end---telco is sending the disconnect DCH 4 UIPE_IMSG CC_DISC_IND REF 00004011 CH 1 1 TOD 10:40:52 CAUSE: #16 - NORMAL CALL CLEARING

datetimeconfig

I was going to suggest the NET data DITI=YES---------not sure why you are not seeing that in your net data. I would change the FTOP to FRES--that will override any trunk to trunk restrictions---

more then likely is an issue with a bad memory stick----if the card has 2 remove one at a time and if it's one of the memories it will boot up. To replace the card just swap the dongle and fmd-------it should come right up.

The 1st thing I would try to do is narrow it down---is it only when I dial thru the 1000M or can I duplicate it by just dialing the 1000M.

The admin ntp I'm looking at says RCAP NDS release 25.40