Search results for query: *

NVM 4.1 Upgrade package English Part #NTAB3391

What type of modem and what setting are you using?? Let verify that first. You are using the modem for remote access correct... Ramon Flores TDSC Voice Engineer

Sorry to tell you this the cost of the spectralink wireless system is no way cheap, you will need the MCU, basestation, wireless phones w/batteries and charger, cables and 66/110blocks. The quote I got for my phone lab was $2750. A single MCU can cover between 5000-50,000 square feet. Additional...

The spectralink wireless phones will used 1 port (per wireless phone) off your MLX408 digital card. If you go to avaya.com you should beable to download the installation and operation guide. The legend/magix will use link150 used for 4 wire PBX/Key. You can also ask for a analog version, I...

Yes it will work with the Legend/Magix. Ramon Flores TDSC Voice Engineer

Spectralink would be my first choice. I have done over 30 installations of the spectralinks on the Merlin Magix. Also have done over 10 spectralink installation for the Nortel Norstar. 10 replacement installation of the transtalk 9040 or 9031 for the spectralink wireless. Spectralinks is by far...

Its possible you have a bad stick of RAM. Do you have any spares. Try swapping them out one at the time. There are also programs out there that can test your RAM. I don't have any at the moment. Well this is a start. Ramon Flores TDSC Voice Engineer

Thank you everyone for your help, so I guess the only option I have is to use the option 7 in voicemail since are client does not like to spend money on upgrades. I will have to talk are client into setting up restrictions, Considering this can open up the site to further toll fraud.

Its setup to use Pool A, which should be the PRI.

The routes are setup to use PRI-A. All sets have access to PRI-A. The absorb digits under desicodes, I think that is what your asking has the following 901 absorb:2 and 902 absorb:all. By rights 901 absorb:2 should not work, I have tried to change it to absorb:all with no luck. Ramon Flores...

I can dial a local and LD number fine, but I can not call forward or line redirect to a local number(cell, pager, phone will not work). It only works for LD numbers.

Hello everyone, here is another CFW off net issue. I have a Norstar MICS DR4.1 w/PRI and a NAM 4.0. The set is setup with redirect:Y and redirect ring:Y. The set has prime line:I/C with 2 I/C assigned. The set has 2 apprs of the DID number. Switch is setup with 2 routes, 001 is used for local...

Sorry for the misunderstanding rcrow490 Ramon Flores TDSC Voice Engineer

Most tech understand you must use the change command. Ramon Flores TDSC Voice Engineer

Thank you f0netech for your help. I found the issue. The routing was done in Audix under auto-attend rounting rounting-table. Removed the incoming called number and everything is working fine now. Ramon Flores TDSC Voice Engineer

Sorry but my secondary ext is blank on my audix sub page 1. Any other suggestions. Ramon Flores TDSC Voice Engineer

Morning everyone. I have a Prologix Rel 6 that I am looking for help with. My coworker per her notes stated that she was able to change the AA routing feature to allow calls from one station to go to another station's voicemail. Can someone direct me where in the switch/voicemail were this...

Have you tried a firmware upgrade...

Tom2129-This would depend on what you need the system to do. If you give me a breakdown on what your EU would like the system to do, I can only give you info on the Norstar (Avaya and Nortel is what I specialist in). I would be more then happy to help you out on this. Ramon

Tom2129-This would depend on what you need the system to do. If you give me a breakdown on what your EU would like the system to do. I would be happy to help you out on this. Ramon