Search results for query: *

Hi, I am Facing a problem in contivty 1100.I am getting into the Debug mode while booting.It shows Embeded OPCODE single trap and gives the prompt E34DB: Can anyone help. Regds Prakap

I had checked the power supply output and earthig also,all meet the spec.I also checked by using new chassis and power supply but the problem still persist.

Hi all I am facing a typical problem in FALC card of 11C mini.Some type of noise is coming in FALC lines.I don't know why.I have checked all things in my mind.Atleast I have checked by configuring a chassis having only SSC and FALC card the noise is still there. Can any one help me if he had...

BUG115 BUG115 : 00004602 03316761 00000223 00008318 00003548 00000000 0 00000000 000000 00 00000000 0 6763 00000088 00006618 0000A213 00000000 00000000 00000000 000000 BUG115 + 0066CDBC 00750ACA 0074F969 00734730 0089BC61 BUG115 + 013B36E7 013B0C52 013A31CC 013A4526 013A3A37 BUG115 + 013A21C9...

Hi, In 81c i'm seeing lot of BUG115 Error. Could you please help me what's this error indicating and a solution to eradicate this. Thanks Prakap

Hi, In 81c i'm seeing lot of BUG115 Error. Could you please help me what's this error indicating and a solution to eradicate this. Thanks Prakap

Hi, I'm configuring DTI Card with Router. Can anyone tell me the pin details at both ends. one of my end is RJ-45 and other end is 9 pin female. Thanks Prakap

Can this be possible by configuring both Meridian in Leader/follower mode.and If the connectivity between both systems goes down the follower declare itself as leader or not.How to configure in leader follower mode.

Hi all, I have some query actully the Connectivity diagram is as follows: M1-----R1-----------R2----M2 M1 is Meridian 11C mini 1st system,M2 is Meridian 11C mini 2nd system.R1,R2 are routers having G.703 card.The connectivity between R1 and R2 are given using E1 stream.IP Phone connected to...

Hi Riaanl, It is ITG Card Version Ip Line 3.0.I am able to ping IP Phone And ITG card IP from LAN.IP Addresses are as follows: Ethernet - 10.10.10.2/24 Leader Ip - 10.10.10.1/24 ITG Card IP- 192.10.1.250/24 IP Phone IP- 192.10.1.150/24 Voice LAN G/W IP- 192.10.1.200/24...

Hi all, I am facing a problem in Meridian 11 C ITG card.The LCD display of ITG card shows L000, But IP phones are not regestering.I checked the status of the card in LD 32 it shows DSBL (TRK IPTN UNREG OWK/OWK). I am able to ping IP Phone from the PC connected to exchange.But not getting...

Hi all, I had gone through your replies,and note down the error the console was showing, "PDT-Unable to restart Debug event handler path cold initialisation error warm start begin-reason 36 found unused block which is erased network interface is up." Again OS restart. Also tell me how to...

Hi, I am facing a problem in meridian 11C mini.The system is getting warm restart again & again.It is not going to console Gives OS Restart.The message before restarting is "Login initialisation error,Unable to set priority for SL1." Can any one tell how to rectify this problem.Is software got...

Dear Sir, I am sending the details of the configuration of meridian I have done.IP Phones on different network are not able to connect.They are showing "Server Unreacheable".In between both the networks((140.4.12.112/255.255.255.248 and 140.4.12.120/255.255.255.248)there is a F/W without any...

Hi I have lost my ITG card password,can any one tell me how to reset ITG card configuration to default.Actually I have to change the IP address of ELAN & TLAN,but I am not able to login to ITG card. Thanks

Hi, I have to connect two nortel Meridian 11C mini using E&M trunk.But I have not implemented earlier.Can any one help me by telling the Pin connectivity of the cable used between two meridians and the configuration of E&M trunk. Thanks!

the following error message pop up after every 1 sec request is rejected by the registered tn,"tn=006400,hwid 210.1.1.2:00" what does it means. can any one suggest.

Hi All I am unable to connect IP phones and receiveing message "request on registererd tn rejected" I have configured the supl in ld 97 and physical tn in ld 14 and ip phone ext. in ld 11. pls suggest. Pradeep

I want to know if I want to manage My Meridian through NNM placed in some different network than ELAN & CLAN/TLAN.What I have to do so that I am able to stablish communication between NNM server ELAN & TLAN.(i.e I am able to ping my NNM server,TLAN & ELAN from Meridian console.Pls help me.

Thanks, I have to change only active ELNK or the ELAN IP of ITG has also to be put on the same Network(i.e 80.0.0.0/8). I have to manage the Meridian using NNM. For that I have to give any SNMP communities and SNMP server infomation at Meridian.pls help me.