Search results for query: *

Thank you! I've just been reading and that feature is not mentioned - but the software is a free trial so I've got nothing to lose. Do you have a model of USB or wireless headset you would recommend? I've used Plantronics and Jabra headsets with Microsoft's OCS with good results. Paul

Hi, We've got a TDE200 and a TVM200. I'm been experimenting with the "two way record" from a single button push - works well. We've looked at automated call recording software for certain lines in our company - it is expensive. Is there a way to automate the two way call recording so it...

Follow up... Thanks to everyone, especially cwc3, for continuing to bang your heads against the wall on this one. I gave up in the end. My main purpose was to get a separate fax system dialling out using H323. In the end, I installed a separate modem connected to an outgoing line rather then...

Tones sent back? Not that I'm aware... COS - everything is set on 1 except TRS lock, which is 7 Under the actual port settings of the PRI card, the following are set on the Supplementary service tab. I wonder if any of these are having an effect? COLP = No CLIR = Yes COLR = No CNIP = No...

The cell phone does NOT ring if you call it from a TIE line out. Paul

Short answer - yes. Long answer - I have 15 lines on a partial T1. Lines 17 to 20 are the tie lines. If you make a call out trying to use tie line to CO, line 17 and one CO line both light up for just a moment - then drop. Paul

I'll leave it alone! :-) Yes - you call any extension in any branch and they can transfer the call out, no problems. Paul

Well - it all the COS settings seem right and trunks look in order. I think I'm going to start taking screen shots & attach them - something might stand out. On the V-IPGW16, Shelf Proparty page, the Trunk Property is set to Private. Should it be set to Public? Paul

I appreciate the amount of effort people have put in to solve this. The Panasonic guys who first programmed this said it 'should' be working - good to hear you have seen this working between 2 other PBX's. When I first started looking at this, 91 was in the first PBX's TIE table and I removed...

This is exactly how it is already set. I double checked all of it. All extension calls work fine. From 91, dial 92 and 10 digits - rings once, a long pause, then a busy tone. This happens from all locations trying to call out from all other locations. You said "Remember to set the number...

Well - my 222 says caller id features? All the good stuff regarding Tie to CO starts on page 332 (section 1.30.1) - and yes I've been reading. I can call all extensions no problem. If I set a PBX code - my extension dialing stops working. If I call anything other then an extension - I get a...

Thanks - thought I had all the manuals, I was missing the features one. Reading, experimenting, reading, etc... :-) Paul

Interesting. I setup a spare DID to go to 195 directly. Called it from my cell phone, it worked perfectly. 91 1 604 xxx xxxx dialed out as expected, call connected, no problems. Hmmm - why will it not allow my tie lines to call out via DISA? Paul

No - I cannot. My local access feature on this PBX is set to 91, (92 on the second PBX, 93 on the third). I call the DISA & hear the message. I dial 91 & hear a dialing tone. I dial the 7 digits - there's a pause, then a busy signal. Paul

Apologies, the other work stuff got in the way, I can get back to this now. 100 is in use. I set it to 195, recorded a simple voice message, set security to none for testing. I can call it from a tie line, hear the voice message, and then dial an internal extension. Works fine. I cannot...

Thanks again guys, CWC3 - Yes, I would like to connect to the other TDE & dial on thier nickel. I do not need a recorded dialing instruction message. Yes - our numbering is 1xx at branch 1, 2xx at branch 2, 4xx at branch 4 (branch 3 did exist, it went away). I call other extensions in other...

Thanks guys, I've gone to 5.3.2, entered 501 in the first slot. When I look at the extensions list - I can see 501 as OGM(DISA) I added 5XX to 2.6.1 When I call 501 with the intercom button - I get a busy signal & 'reorder tone' on the display. When I call 5019xxxxxxxxx or 75019xxxxxxxx...

Hi, I have 3 TDE200's, all connected using the IP-GW. How can I place a call from one PBX to another PBX using the TIE IP-GW connection but route the call outwards? For example - if I could place call from PBX 1 to PBX 2 and then use PBX 2 to get to the outside world, it would save on long...

OK - it's fully working. Calls to extensions on each system work fine. I need to work out how to dial an external number from Asterisk via the Panasonic (the panasonic will allow internal calls but not external) I'm a bit busy at the moment, but when I get the chance, I should write up the...

Me too - but I spoke to a guy in Calgary who says he has it working 100% with no problems, (Asterisk to Panasonic IP-GW). From what I'm reading, I 'think' there's a bug in the very latest h323 (ooh323) in Asterisk and that's what causing the calls to drop. I might try going back a few versions...