Search results for query: *

Does anyone know if you can remove the function of the fixed key drop on 54xx phones? Thanks.

Thanks, all slot B did fix it.

New install IPO 406V2 3.0.69. The IPO is seeing the single PRI card in Slot A as a BRI card? Any Ideas??? 1mS PRN: Monitor Started IP=192.168.1.103 IP 406 DS 3.0(69) AristrePBX 1mS PRN: LAW=U PRI=0, BRI=4, ALOG=0, ADSL=0 VCOMP=0, MDM=0, WAN=0, MODU=1 LANM=0 CkSRC=0 VMAIL=0(VER=0 TYP=1)...

Do you have any cheets or information on a hotel enviroment install?

Does anyone know how to program it or install it?

Had the same issue with .40, Tier 3 upgraded to patch 67903, then we upgraded to 3.0.69. It is either the software or the PRI is coming in too hot. The db on the line can effect the PRI in many weird ways.

Thanks dwalin. But the data is all cisco and the IT dept did their Qos, I think this is the issue, not to mention I believe you cannot run pass-thru at 729 for the faxes correct? We only have 711 as the primary and only codec, so my thoughts are that the bw is filling up and we don't have any...

Well thanks Bernie....We found that the far end G3 had a router typo on the ip address of the gateway. Changed and all is well....

Implemented IP Trunks via CSI and G3I, site is fiber between but getting a BW Prowler error. Also choppy talk path but we are not showing jitter or packet loss on the trace? Should each site have its own Network region? If so why?

Can you use HTTP for file distrubtion on the 46xx phones?

Definity CM1.2 and CM1.3 Setting up an IP trunk and getting this when dialing across it then a fast busy? Any ideas? H.323 sig group is up and fine. Trunk group is up and fine? Just cannot use the IP trunk. Thanks.

Magix 4.0 with Intuity. 3 Cabinets with MLX phones. 8 Copper lines and 1 PRI. The issue is for no reason sporadically throughout the day you go to pick up and dial out and get a busy.....Doesn't matter if long distance or if local etc. The CAS is showing that the PRI is not being overused...

Bill -- Didn't work, but I will be there in a few days to test further. Will let you know.

Yes...Thanks, So they can use the PRI without having to dial 9 from a 54xx set right?

Situation....IPO 406V2 3.0.59 with 3 copper backup lines and 1 PRI. Customer doesn't want to dial 9 to go to outside line. Can this be done? They want to pickup phone on call appr a and dial 10 digit number?? Any ideas?

I know this has been asked before, but is there anyway to have a vmail message into one mailbox be outcalled notified to over 14 telephone numbers at different intervals? Can VB scripting do this??? Any ideas would be greatly appreciated. VMAIL

Does anyone have a step by step on upgrading the VOIP firmware on an S8300 with 3 media gateways? Thanks,

www.alarmtraq.com Tell Jim that Jamie sent you.

According to Avaya Tier 3 they state to set it to 100/half, which I did on the extreme side. I don't know how to turn off/on the Qos for that port on the IPO? Do you do this on the extreme side? Here is the IP Routing Table..... Routes are (3 of them): IP: nothing Mask: 255.255.255.0...

O.k. Tell me if I am crazy.... I have a customer that has an IPO 406v2 3.0.44 with 16 co lines and 1 24 channel t1. DNIS for over 45 toll free numbers coming in on the t1. Each toll free has its own dnis of 4 digits to the IPO. The customer wants the ability to see on their phones, (5410's)...