Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. Jigman32

    Single digit NXX

    Can you program an NXX in an opt 81c running succession 3 as a single digit. Having all 2 , 3 , 4 ,etc. going to the same rli?
  2. Jigman32

    Analog to digital wont work

    I assume you mean "That's the fix" as in dont use it. I think I learned my leasson on that.
  3. Jigman32

    Analog to digital wont work

    I came in early today and did a hard reset of the PBX by shutting it of at the breakers. This fixed it. I geauss a zero got stuck and a hard reboot unstuck it. I tried disableing the shelf then the controller and reseat the controller, but that didn't work. Thanks for all the help and advice I...
  4. Jigman32

    Analog to digital wont work

    Regreatably no I did not out them. I have tried the cardslt cmd and it doesnt seem to work for me. If I have an analog phone prog. on the card it say i can't because there is something on it. If I del. what's on it it say it can't because it is unequiped. Most likely I am not doing it correctly.
  5. Jigman32

    Analog to digital wont work

    Thanks KCFLHTK and SL1M1 I will try that. I hope that will work and it's not a corrupted database.
  6. Jigman32

    Analog to digital wont work

    What confuses me about this is the fact that I had analog lines working on the same TN's prior to me moving them to another card using LD 25. Then putting a digital card in the same slot, and it's not just one slot it's about 5 that I have moved and can't get the digitals to work on. I have...
  7. Jigman32

    Analog to digital wont work

    When the phone is plugged in it blinks once then goes dead. There are other digital and analog phones on the same loop, and they work. I am using 2616 set's. Yes I have disabled and enabled ports with same result. I have IDC the card it is an NT8D02ea. DES TEST TN 020 0 12 01 TYPE 2616...
  8. Jigman32

    Analog to digital wont work

    cmassjohn: Sorry about the are you serious comment earlier I read your post as cord not card. Yes I am using digital line cards. To clarify a little more. I moved a bunch of analog cards to empty slot on the same shelf. Then after the cables had been terminated to the new blocks we went back...
  9. Jigman32

    Analog to digital wont work

    KCFLHTK: We have tried to reverse polarity and still doesn't work. cmasjohn: Are you serious about the digital line cord? I am outing the digital and programing the tn as analog OR digital, and putting the appropriate card in the slot. Thanks for the help
  10. Jigman32

    Analog to digital wont work

    I have an 81c with succession 3.0 on it. We have been redoing the cabling on the TN side. Going from 66block to wire wrap. I have been using the mov command in LD 25 to move whole analog cards. The digitals I move one at a time and no ACD sets are being moved. It has been working fine until we...
  11. Jigman32

    One way audio

    I swapped both per sig cards and it seems to have done the job. At least nobody is complaining anymore.
  12. Jigman32

    SYSTEM MONITOR

    Good advice Thanks. Can't do it without you sometimes.
  13. Jigman32

    SYSTEM MONITOR

    I did the exact thing you suggested last night and got it working. I did discover that the satin line cords have to be plugged in a certian way. I had to flip all my line cords to get it to work. Thanks for the help.
  14. Jigman32

    SYSTEM MONITOR

    I am having problems getting my system monitor cards NT8D22 working in my 81c. I have double and triple cheked all the dip switch settings. I have tried new cards and cards that I tested in my 61c that worked fine in the 61c. I did notice that in the installation instructions it shows an...
  15. Jigman32

    SDI CARD

    Thank you johnpoole, pronei and ghtrout. It was the way the paddleboard pinned out. Turns out that 6 on the paddleboard is the recv not 3 like it usually is. So 6 on board goes to 3 on dumb term. I found this info at http://www.ghtrout.com/ghtrout/index.html Thanks to all the other who tried...
  16. Jigman32

    SDI CARD

    The paddle cards are original to the switch.
  17. Jigman32

    SDI CARD

    The 9 pin RS232 plug is the same on both isn't it. I know the cores use a 25 pin, but I have a 25 to 9 pin adapter that I use.
  18. Jigman32

    Networked MIRAN

    Currently each switch is just set with defaults. What is vni?
  19. Jigman32

    Networked MIRAN

    I have 4 opt switches 2 81c and 2 61c. They are all networked together via cdp with 2 PRI's between each switch. Is it possible to route intercept treatment for all the switches to 1 central MIRAN card?
  20. Jigman32

    SDI CARD

    I have tried 2 other cards they are just the 2 port paddle boards, but I get the same result. If you mean wiring from the tty to the dumb terminal then yes im sure its good. I can use the same cables to access the core tty ports with the same terminal.

Part and Inventory Search

Back
Top