Search results for query: *

Just did and it works.. PHEW! Thanks. Joe

Hello all, I am really struggling with a re-installation of a Flash vmail. I installed the two ports (4 channels). However, I cannot get into it via F983. I keep getting inactive feature. In fact, I get this with all Feature codes used for vmail. When I dial the DN of the Vmail (241), I get...

Hello all, I am really struhggling with this Flash 2.1. I installed the lines as above. However, I cannot get into it via F983. I keep getting invalid feature. In fact, I get this with all Feature codes used for vmail. If i dial the DN of the Vmail (241), I get a login. If I dial the DN...

Right. The expansion is in there. I will go back tomorrow and remove two ports from the wiring. I think I need to re-initialize as well. Thanks for your Help! Joe

Thanks CurlyCord.. I was putting two KSU ports on each jack. I thought a 4-port Flash needed 4-ports of KSU. Joe

Hi, Somewhat new to Norstar and wondering how I wire up a 4 port Norstar Flash. I thought i wire up two phoen ports on each jack, but didnt work. I installed one port on pins 2 & 3, and the other on pins 1 & 4. I did the same with the 2nd RJ11 jack for a total of 4 phone ports. Is this not...

I was working with this agai this morning and from my ASA I can ping the VLAN gateway which is on the same subnet as the PBX. However, I cannot ping the Corp LAN IP address. Is there something I need to program in the Avaya to see the subnet of the Corporate LAN? Thanks!!!!!, Joe

Yes, I can ping the Vlan port address from the routers. Thanks. Joe

Mitch or ?? I am in the system now via the web IP. I dont see where there is an "ip interface page" as stated above. I did find a page to option the interfaces and the only thing there was three LAN connections with their respective IP addresses. There is an option to check for VLAN. I...

Ironically, If I put circuit 2 into the tn464 card, it comes up. If I put circuit 1 into the mm710 with it programmed as B, I get a different reading on the Smartjack. It shows Up, but the D channel is OOS, as are the channels..

I would like to reach out to the communittee here and ask a telco provider question. As I stated above, I have two identical circuits from the same carrier (paetec). I was recently able to get the 2nd T1 working by changing the TSC Supplementary Service Protocol to "A" in the signaling...

OK thanks, I am remote and dialed into the modem. I'll have to wait until I get on-site. Thanks again!!

Thanks Mitch, I can seee where the Medpro has that option. My question is; If i set the Medpro and CLAN's "VLAN Option" to "2", how does the PBX know what VLAN 2 is, or how does it know to route to the Layer 3 switch's gateway?

Mitch, My VLAN 1 is 192.168.80.180. I have a lot of users working off VLAN 1, which consists of all the switch ports except the one port assigned to the Avaya (VLAN 2). My VLAN 2 gateway is 192.168.169.25. This VLAN 2 is the gateway to the avaya which has all devices with a 192.168.169.xxx...

OK Thanks, The ssh was enabled in the access server screen. In fact, everything was enabled except FTP. I built the SAT in "ch ip-service" I made it as shown. I'm not sure if this is correct, but I still cannot ping any PBX devices from outside the VLAN. Any other suggestions, or should I...

I do have access to the maint web. I'll check that and add SAT. I'll post you back asap. THX!!

Hi, I built a VLAN on a layer 3 switch port that matches the IP subnet scheme of the Avaya PBX (CM 5.2). From the Layer three switch i can ping all my devices on the PBX. However, I cannot setup my ASA to access the PBX's CLAN, or procr port. Is there something that needs to be done in the...

Thanks for the suggestions! We got it working by changing the csu type to integrated (was other), and the bizzare thing was that the "TSC Supplementary Service Protocol: was changed to A". (It was set to "B" like the twin Paetec circuit). Can someone tell me what the differance is between...

Hi, I have a G650 (CM 5.2) that has a 464 tT1 card. The PRI is connected to the Carrier and working. I have a G430 in the same equipment rack as the 650. I want to install a second PRI in the same trunk group as the first, but using a mm710 in the G430. The second PRI into the G430 shows...

Hi, It was a bad G350 gateway. Just as Tier3 suggested. Good luck, Joe