Search results for query: *

what type of extension.... IP, analogue, digital??? "I wish I was @ 127.0.0.1

PELPI's are really the only way to divert with an mx-one well sertantly on a ver 3.1 or 3.2 system. "I wish I was @ 127.0.0.1

I have tried this as well.. and found it does not work... Why dont you changed the the config file to a default and one and reboot the phone???? it is the most likely the easyest way to do it. "I wish I was @ 127.0.0.1

This is documentmented in ALEX.... well for TSE anyway! under installation DBC 4422 you will need to telnet or SSH to a handset and use the command stated with in alex to change the password. sorry I dont have ALEX infront of me right now. it will then given you the password you have choosen...

cheers I will check it out! "There is no place like 127.0.0.1

Hi all, I am new to firewalls.... I wish to install another interface card to facilitate a DMZ config. Could someone please advise me what part I should order for a PIX 515E ver 6.3(1) Many thanks in advance "There is no place like 127.0.0.1

I need to use 3 interfaces "There is no place like 127.0.0.1

Hi all, I have been a given PIX 501 ver6.3(4) and asked to config DMZ but can not find any info how get this done.... is DMZ supported on this version of PIX????? "There is no place like 127.0.0.1

the deault is "admin" and password is "Ericsson" case sensitive. the telnet session is really only used for trouble shotting as whosrdaddy said...... However there are some other cool functions that are supported like Simualtekeypush. this is also where you need to telnet to to change the web...

indeed you are correct group switch is supported from TSE 3.1 onwards "There is no place like 127.0.0.1

try this site http://www.bandcalc.com/ "There is no place like 127.0.0.1

No worries thank you for the correction Alpha008.. "There is no place like 127.0.0.1

acording to your print eth1 192.168.1.160....not 10.10.10.10 are sure you IP configs are correct?????? that may explain why you are getting No contact with MGW. and is'nt 10.10.10.1 a broadcast address anyway??(Can someone confirm for me) "There is no place like 127.0.0.1

Hi guy's, I am currently running at; eri_sn_admin@lim1:~> ts_about ====== MX-ONE Telephony System ====== Version: 3.1 SP1 Hotfix build7 RPM Packages ============ Telephony Server 11.43.5 : eri_sn-11.43.3-MR eri_sn-11.43.5-CR Media Gateway File system 2.0 ...

What firmware are you using on the IP Handsets? there are versions of IP handset firmware where this a known issue "There is no place like 127.0.0.1

telelion, they are all stock standard Ericsson single RU TSE's however Lim6 10 & 11 are classic Chassis. "There is no place like 127.0.0.1

I did a seach for "fail" in the feedback logfile and here are the results. MDSH> /* Failed to find the header */ REEXP:DIR=ALL; number_conversion_print -conversiontype 6 NOT ACCEPTED DIR NOT REMOTE EXTENSION MDSH> GEDIP:LIC=ALL; NOT ACCEPTED LICENSE(S) NOT INITIATED MDSH>...

Hi whosrdaddy, I read your post.. thank you my DNA is running 5.5 with no SP.however regrdless of the SP this worked well until the Coruption. I will only upgrade to a different SP if it is 100% needed and in this case because it once worked well I dont feel it needed. "There is no place like...

I have been through the log file and found that a key print for a generic extension was giving wait!wait! lost command. I have since killed the extension off and re built it. Now when I run a sync all GE ext's key prints are fine and everything else looks good in the log file but GE exts are...

Hi All, I have a Mx-one TSE 3.1 sp1 In the past I had GEFKP corption due the calalt being changed on access 1 and 2 on handsets. I have now clean up all corption non the PBX however when start a syn for DNA I am still getting fail on generic extensions. do anyone have any ideas to fix...