Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

MX-One 3.2 Media Gateway

Status
Not open for further replies.

TeleLion

Technical User
Jan 4, 2006
326
US
Am trying to run a MX-One one lim system (MX-One server + MediaGateway) I keep getting the following alarm in TS:

Code:
Global status: Severity0:0-0, S1:1-0, S2:0-0, S3:1-0, S4:0-0, High=3
               Latest erase/reset:   2008-11-28 23:19:53 (UTC)
               Complete erase/reset: 2008-11-28 23:19:53 (UTC)


S N    Handle  Dom.  Code LIM Where    Explanation
===============================================================================
3         641     5     1   1          No contact with media gateway
1         769     1    30   1 AMP-user There are analyzed core files to report

MDSH> alarm_list -format allop

ALARM LOG
IDENTITY: (no info)

DATE: 2008-11-29  TIME: 11:16:51 (UTC)
CLASS: 3
5:1      No contact with media gateway
DATE        TIME     ALP        NOIF EQU
2008-11-28  23:19:57 641        1    001-*-**-**

CLASS: 1
1:30     There are analyzed core files to report
DATE        TIME     ALP        NOIF
2008-11-28  23:20:01 769        1


END

Looking at the media gate way here is my configuration and it shows the below error:

Code:
egx > dispar
ROJ_rev*    R3A/A
ROJ_num*    ROJ 208 0031/1
ROJ_ser*    
eth0_mac*    
eth1_mac*    
BFJ_rev*    R3A
BFJ_num*    BFJ 901 03
BFJ_ser*    
eth0_ip     10.10.10.1/28
eth1_ip     192.168.1.160/25
def_route     192.168.1.254
nsf_server     10.10.10.10
egx > tftp take-file error!!
auto-update failure!!!

I can ping for MX-One server eth1 (10.10.10.10) to MG eth0 (10.10.10.1), any ideas?

TELEC3
 
acording to your print eth1 192.168.1.160....not 10.10.10.10

are sure you IP configs are correct?????? that may explain why you are getting No contact with MGW.

and is'nt 10.10.10.1 a broadcast address anyway??(Can someone confirm for me)

"There is no place like 127.0.0.1
 
Tele, please do the command lim_config_print and post it here.

/Daddy

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!
 
DrewMK2, if it is a broadcast address the gateway will almost certainly not allow you to configure on an interface , the problem ( i stand to be corrected ) may be related to tftp configuration- filenames paths etc or incorrect subnet configuration .

”Beginning is half done.”
 
No worries thank you for the correction Alpha008..

"There is no place like 127.0.0.1
 
For your 10.10.10.0/28 subnet, valid addresses are 10.10.10.1 - 10.10.10.14, with a broadcast address of 10.10.10.15.

10.10.10.1 can therefore ping 10.10.10.10 OK.

192.168.1.128/25, valid addresses are 192.168.1.129 - .254, .255 broadcast.

Can 192.168.1.160 ping 192.168.1.254?

What are the IP addresses of the devices which are not communicating?


 
I believe no contcat with media gateway means 10.10.10.1 can not contact 10.10.10.10, but i can ping between them, i think it's a tftp issue since my Media gateway is stuck at:

[bold]egx > tftp take-file error!!
auto-update failure!!!
[/bold]

The media gateway should locate the update files from the TS and update it self, but this is not happening???

whosrdaddy: will provide you with lim_config_print as soon as i get access to the system again.


TELEC3
 
Here you go:
Code:
eri_sn_admin@lim1:~> lim_config_print
                                                                           Network interface
LIM      Host name                       Host type        Default gateway  Address          Netmask
-------------------------------------------------------------------------------------------------------------
1        lim1                            ESU with fan     192.168.1.254    192.168.1.11     255.255.255.0
                                                                           10.10.10.10      255.255.255.240
                                         EMG-1                             10.10.10.1       255.255.255.240

eri_sn_admin@lim1:~>

TELEC3
 
This is so strange, am trying to query the MG (egx_sw-10.13-200809181505.i586.rpm)software on the TS server, when i run a query it says not installed if i try to install it, it says it's already installed!!!! any ideas?
Code:
lim1:/home/eri_sn_admin/install_sw # rpm -ih /home/eri_sn_admin/install_sw/egx_sw-10.13-200809181505.i586.rpm
########################################### [100%]
        package egx_sw-10.13-1 is already installed
lim1:/home/eri_sn_admin/install_sw # rpm -qi egx_sw-10.13-200809181505.i586.rpm
package egx_sw-10.13-200809181505.i586.rpm is not installed
lim1:/home/eri_sn_admin/install_sw # rpm -ql egx_sw-10.13-200809181505.i586.rpm
package egx_sw-10.13-200809181505.i586.rpm is not installed
lim1:/home/eri_sn_admin/install_sw # rpm -ih /home/eri_sn_admin/install_sw/egx_sw-10.13-200809181505.i586.rpm
########################################### [100%]
        package egx_sw-10.13-1 is already installed
lim1:/home/eri_sn_admin/install_sw # rpm -ih /home/eri_sn_admin/install_sw/egx_sw-10.13-200809181505.i586.rpm
egx_sw-10.13-200809181505.i586.rpm
lim1:/home/eri_sn_admin/install_sw # rpm -i /home/eri_sn_admin/install_sw/egx_sw-10.13-200809181505.i586.rpm
        package egx_sw-10.13-1 is already installed
lim1:/home/eri_sn_admin/install_sw # rpm -e egx_sw-10.13-200809181505.i586.rpm
error: package egx_sw-10.13-200809181505.i586.rpm is not installed
lim1:/home/eri_sn_admin/install_sw # rpm -ih egx_sw-10.13-200809181505.i586.rpm
########################################### [100%]
        package egx_sw-10.13-1 is already installed

TELEC3
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top