MX-One 3.2 Media Gateway

[TeleLion]

Am trying to run a MX-One one lim system (MX-One server + MediaGateway) I keep getting the following alarm in TS:

Global status: Severity0:0-0, S1:1-0, S2:0-0, S3:1-0, S4:0-0, High=3
               Latest erase/reset:   2008-11-28 23:19:53 (UTC)
               Complete erase/reset: 2008-11-28 23:19:53 (UTC)


S N    Handle  Dom.  Code LIM Where    Explanation
===============================================================================
3         641     5     1   1          No contact with media gateway
1         769     1    30   1 AMP-user There are analyzed core files to report

MDSH> alarm_list -format allop

ALARM LOG
IDENTITY: (no info)

DATE: 2008-11-29  TIME: 11:16:51 (UTC)
CLASS: 3
5:1      No contact with media gateway
DATE        TIME     ALP        NOIF EQU
2008-11-28  23:19:57 641        1    001-*-**-**

CLASS: 1
1:30     There are analyzed core files to report
DATE        TIME     ALP        NOIF
2008-11-28  23:20:01 769        1


END

Looking at the media gate way here is my configuration and it shows the below error:

egx > dispar
ROJ_rev*    R3A/A
ROJ_num*    ROJ 208 0031/1
ROJ_ser*    
eth0_mac*    
eth1_mac*    
BFJ_rev*    R3A
BFJ_num*    BFJ 901 03
BFJ_ser*    
eth0_ip     10.10.10.1/28
eth1_ip     192.168.1.160/25
def_route     192.168.1.254
nsf_server     10.10.10.10
egx > tftp take-file error!!
auto-update failure!!!

I can ping for MX-One server eth1 (10.10.10.10) to MG eth0 (10.10.10.1), any ideas?

TELEC3

 

[drewMk2]

acording to your print eth1 192.168.1.160....not 10.10.10.10

are sure you IP configs are correct?????? that may explain why you are getting No contact with MGW.

and is'nt 10.10.10.1 a broadcast address anyway??(Can someone confirm for me)

"There is no place like 127.0.0.1

 

[whosrdaddy]

Tele, please do the command lim_config_print and post it here.

/Daddy

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[Alpha008]

DrewMK2, if it is a broadcast address the gateway will almost certainly not allow you to configure on an interface , the problem ( i stand to be corrected ) may be related to tftp configuration- filenames paths etc or incorrect subnet configuration .

”Beginning is half done.”

 

[drewMk2]

No worries thank you for the correction Alpha008..

"There is no place like 127.0.0.1

 

[VinceWhirlwind]

For your 10.10.10.0/28 subnet, valid addresses are 10.10.10.1 - 10.10.10.14, with a broadcast address of 10.10.10.15.

10.10.10.1 can therefore ping 10.10.10.10 OK.

192.168.1.128/25, valid addresses are 192.168.1.129 - .254, .255 broadcast.

Can 192.168.1.160 ping 192.168.1.254?

What are the IP addresses of the devices which are not communicating?

 

[TeleLion]

I believe no contcat with media gateway means 10.10.10.1 can not contact 10.10.10.10, but i can ping between them, i think it's a tftp issue since my Media gateway is stuck at:

[bold]egx > tftp take-file error!!
auto-update failure!!!
[/bold]

The media gateway should locate the update files from the TS and update it self, but this is not happening???

whosrdaddy: will provide you with lim_config_print as soon as i get access to the system again.


TELEC3

 

[TeleLion]

Here you go:

eri_sn_admin@lim1:~> lim_config_print
                                                                           Network interface
LIM      Host name                       Host type        Default gateway  Address          Netmask
-------------------------------------------------------------------------------------------------------------
1        lim1                            ESU with fan     192.168.1.254    192.168.1.11     255.255.255.0
                                                                           10.10.10.10      255.255.255.240
                                         EMG-1                             10.10.10.1       255.255.255.240

eri_sn_admin@lim1:~>

TELEC3

 

[TeleLion]

This is so strange, am trying to query the MG (egx_sw-10.13-200809181505.i586.rpm)software on the TS server, when i run a query it says not installed if i try to install it, it says it's already installed!!!! any ideas?

lim1:/home/eri_sn_admin/install_sw # rpm -ih /home/eri_sn_admin/install_sw/egx_sw-10.13-200809181505.i586.rpm
########################################### [100%]
        package egx_sw-10.13-1 is already installed
lim1:/home/eri_sn_admin/install_sw # rpm -qi egx_sw-10.13-200809181505.i586.rpm
package egx_sw-10.13-200809181505.i586.rpm is not installed
lim1:/home/eri_sn_admin/install_sw # rpm -ql egx_sw-10.13-200809181505.i586.rpm
package egx_sw-10.13-200809181505.i586.rpm is not installed
lim1:/home/eri_sn_admin/install_sw # rpm -ih /home/eri_sn_admin/install_sw/egx_sw-10.13-200809181505.i586.rpm
########################################### [100%]
        package egx_sw-10.13-1 is already installed
lim1:/home/eri_sn_admin/install_sw # rpm -ih /home/eri_sn_admin/install_sw/egx_sw-10.13-200809181505.i586.rpm
egx_sw-10.13-200809181505.i586.rpm
lim1:/home/eri_sn_admin/install_sw # rpm -i /home/eri_sn_admin/install_sw/egx_sw-10.13-200809181505.i586.rpm
        package egx_sw-10.13-1 is already installed
lim1:/home/eri_sn_admin/install_sw # rpm -e egx_sw-10.13-200809181505.i586.rpm
error: package egx_sw-10.13-200809181505.i586.rpm is not installed
lim1:/home/eri_sn_admin/install_sw # rpm -ih egx_sw-10.13-200809181505.i586.rpm
########################################### [100%]
        package egx_sw-10.13-1 is already installed

TELEC3