Search results for query: *

sorry 4 to 11 is an another problem about dialing, no iclid, i see exactly the same problem only 4 digits shown on the iclid , when i upgrade one 3.1.56 system to 3.2.53, i can't solve the problem, roll back to 3.1.56. i think we should export settings , delete conf and upgrade the unit...

i think the problem is that 191784873mS SipDebugInfo: License, Valid 1, Available 1, Consumed 1 191784874mS SipDebugInfo: Outgoing Call in excess of License: Consumed: 1, Available: 1 what is the solution about this error message. i have sip trunk channels instance 1 licence, i can dial...

hi i make this conf , and it is working, but it says unobtainable , and calls cant success, is there a way to achieve this avaya ip office small office edition 4.0.(5) local argentina i write only system shortcode 8N; dial N"@ipaddress" 9 please help me thanks serhan from cablenet

are the bri trunk lights green ? my bri lines arent green, they are unresponsive, i think my problem is about lines, not ipo configs. should i try 4 wire cable or just utp cable is enough.

hi i want to set quad bri trunk on avaya 406 i have 2 isdn output with RJ45 with 2 wire cables i put one 2 wire cable in nt1 unit, and i connect the nt1's isdn output(4 wire) to the avaya's quad bri port, but when i dial outside it says disconnect, and incoming calls always busy, is there a...

we can transfer internal calls via flash button.

you can raise dial delay count 4 to 11, this fix the problem.

thanks intrigrant, i will try this, thanks.

hi when when we reset the ip office 412 , the extension's flash buttons begin working one by one, every reset one extension begin to work, and working extensions dont work again, what is that problem, do you know this problem, how can we achieve this, thanks serhan from cablenet

hi my conf is that 8 . secondary dial tone 100 [8]0XXXXXXXXXX dial [8]0N 100 [8]00XXXXXXXXXXXX dial [8]00N 100 can you please give me an example 8 . secondary dial tone 100 [8]0XXXXXXXXXXa; dial [8]0Na; 100 [8]00XXXXXXXXXXXXa; dial [8]00Na; 100 like these? please give me an example, and...

hi thanks i read the pdf's of this shortcode and i send the set absent text short code message's example's to the customer, i will try it , thank you. it is good, but is there any user friendly version, for example the digital phone says the extension busy or no answer like vm pro's assisted...

hi after reboot i can dial England phone numbers 3-4 times and after these 3-4 conversation, i can not dial again this numbers, i can dial cell phones , but i cannot dial international numbers, after rebbot i can dial again.

Hi can you please look at that problem, the problem was about Cause=127, ConfMove(IPO)/Interworking unspecified serhan from cablenet

Hi i have a ipo 412, version 3.2.55 and 5410 handsets, and our customer wants to know, if 5410's can make decision about the station busy or no answer without using voicemail pro, if users have appearence keys like a and b, they can see second call on b appearence key, in this case is it...

Hi, i have a problem about dialing international calls from ip lines avaya 406 connected to the cisco 1841 router, and this router connect to the g.shdsl line to the service provider. H323 forwarding this router to the ipo The specifications are ip office 406 , vcm 4 , version 3.2.55 locale...

ok manufacturer's values min 500 max 600 solve the problem, thanks.

i dial the analog handset manufacturer's hotline and they say karel-ladin analog handsets flash hook pulse width values are 500 ms minimum and 600 ms maximum, what do you think about these values, is it correct, should i test these settings, i will try your values and their values thanks,

Hi, i have a problem about transfering calls to the another extensions by pressing flash button, avaya 412 ver 3.2.55, locale US(Kingdom) for example user 1 calls user 2 , and user 2 wants to transfer user 1 to user 3 , when user 2 push the flash button on her analog handset , user 1...

Hi, the error messages was cause 16 and cause 1 Cause No. 16: normal call clearing. This cause indicates that the call is being cleared because one of the users involved in the call has requested that the call be cleared. Under normal situations, the source of this cause is not the network...

version 3.2.55 vmpro 3.2.30 ipo 412 intrigrant i send you the config file.