Search results for query: *

What is the command to mirror a port on a router? I need to mirror an ethernet port.

My document says that I need to mirror the port that the firewall or gateway is using so mirrored port can see all inbound and outbound traffic. The port below is the port Im using for all traffic. What is my command to mirror the port below?? interface GigabitEthernet8/47 description...

Guys, I'm looking to mirror this port for websense? My first question is how do I know if this switch is able to allow BI-directional spanning, and how do I mirror this port if Im running Catalysts? How do I found out if this switch is catalysts or native anyhow?? interface...

I didnt know what the exact command was to enable the T1 for voice instead of a data T1? I dont have the module in the router yet, so I cant do a sh run..

What is the exact IOS commands to turn up a VMIC 1MFT-T1???

What is the correct commands to turn up a Voice T1 on this module?

What is the command for running the 2939 debug on the router, and how does it work? I'm adding a new Voice T1 to my router.

Guys, for the life of me I cant remember what the command is, and I just used it a couple of days ago. I want to look at an interface from the running config and see on the equipment it is plugged into what port it is connected to?? example: sh run int g0/2---- what the port is it is...

This is the port on the switch that connects to the server DR-3020-Bay2# interface GigabitEthernet0/2 description DR-ESX2 vmnic3 switchport trunk encapsulation dot1q switchport trunk native vlan 99 switchport mode trunk speed 1000 spanning-tree portfast The port channel on the switch...

This is the ping results from the switch.. DR-3020-Bay2#ping Protocol [ip]: Target IP address: 10.171.2.51 Repeat count [5]: 50 Datagram size [100]: 100 Timeout in seconds [2]: Extended commands [n]: Sweep range of sizes [n]: Type escape sequence to abort. Sending 50, 100-byte ICMP Echos to...

I get the same response when I ping from the switch, it pings successfully twice then dies? DR-MDF-Stack1#sh int vlan 54 Vlan54 is up, line protocol is up Hardware is EtherSVI, address is 001d.46c0.0bc7 (bia 001d.46c0.0bc7) Internet address is 10.171.2.1/24 MTU 1500 bytes, BW 1000000...

Im trying to reach a VM server, the address is 10.171.2.51. Im pinging from switch 10.169.1.2 g1/0/3 to switch 10.169.1.11 g0/17 and then that goes to a VM server that is configured 10.171.2.51 gw 10.171.2.1 It will ping successfull twice then die, what do I have setup wrong??? 10.171.2.1 IS...

What is the command to put a description under a vlan??

Ihave a 7960 cisco phone plugged into my data jack then my laptop runs off of the phone. My problem is when I try to connect a small hub into the jack? When I use a small hub I cant get the pone to work, the expansion module just lights up red and flashes and thats it, any idea? It is a 4...

I have a new juniper firewall 10.169.x.x and I just want to add it to my 2900 switch port so I can see it on our network, what is the quickest and easiest way to accomplish this?? Thanks!!

GUYS, HERE IS AN EXAMPLE I HAVE TO CHANGE FROM ROUT 18 TO ROUT 10? RLI 60 ENTR 0 LTER NO ROUT 18 TOD 0 ON 1 ON 2 ON 3 ON 4 ON 5 ON 6 ON 7 ON CNV NO EXP NO FRL 1 DMI 31 FCI 0 FSNI 0 SBOC NRR OHQ NO CBQ NO ENTR 1 LTER NO ROUT 10 TOD 0 ON 1 ON 2 ON 3 ON 4 ON 5 ON 6...

Guys, we did a circuit upgrade and any RLI that was routed through RLI 18 now has to be routed to the new RLI 10? What is the steps to change these?

NO.. Its the local area code for that site.

Cannot dial 248 733 2954 If dialing 733 2954, gets recording to dial area code. If dialing area code, gets fast busy. I get this error when I try to enter the prefix. I checked and its not in the switch? REQ NEW CUST 0 FEAT NET TRAN AC1 TYPE NXX NXX 733 ESN073 NXX

8911 is built as a 2500 set at Lyon Meadows. Per Cindy’s request please build a phantom ACD queue at Lyon Meadows that is a DID number and that NCFW’s to 8911. Then point 8911 at the aforementioned locations to the Lyon Meadows ACD (DID number) queue. I can help you with this if need be...