Search results for query: *

Hi - I am ok thanks - good to see you here. Yes I have a spare 50B as well as wa workign standard 50 with an expension 4 x BRI module. I was wondering if I could consolidate into a single unit with one analogue trunk and one BRI trunk, but it looks like that's not possible. It'll all...

Hi I think this is a logn shot, but wonder if anyone can help. A Nortel BCM50b has 2 BRI ISDN ports. Does the unit have the harware also to support an anaogue trunk. Ie can one of the ISDN ports be disused and the system configured to use an analogue trunk connected via the 25 pair...

I get occasional System out of memory alarms on a BCM 50/R6 too. It is fully patched. Doesn't seem to affect the running of the system

That'll teach me! I found that if I tried to run the run/bat file myself it wouldn't work, but if I created a new shortcut to it, it did...

Has anyone got Business Element Manager running successfully on Windows 10? When I try nothing happens. I have Java loaded, with MD5 enabled again (via editing java.security).

Has Avaya have stopped support? I understood they would support BCM until l2018? Surely that means they need to support Business Element manager on later Java versions?

I suspect you are seeing general scanning for open SIP ports on the internet. I tried this a while back and would get spurious calls. I suggest you talk to your SIP trunk provider to find out their own IP ranges and tie down firewall access to allow SIP traffic from the trunk provider through...

If you have VoIP or SIP gateway licences on both you can link them together using IP...... You would configure this under Resources ->IP Trunks

yes it's working well now - I hadn't considered messing with that initially

I finally solved this one. It was a problem with the source system (ie the one without it's own external trunks). Under Dialing Plan -> Public Network the DN length of '9' in the Public network DN lengths was set to 4 I could see from BCM monitor that after 4 digits it would route the call...

I have not had a chance to try DISA yet but I have had a chance to try this on two systems that both have an MCDN keycode now Unfortunately I get the same result - extensions calls across the network are fine, but when accessing a remote systems trunks when dialling the external number randomly...

Yes I am very much just trying to allow one system to use the trunks of the other. I will try a DISA config. The issue seems to be that when the central systems line is seized there is a slight pause and during that time any dialled digits from the remote system are lost. Dialling very slowly...

Thanks for following up - I am wondering that. I haven't seen any Avaya Docs that clearly state that MCDN is needed for this type of tandem calling, just centralised voicemail. However since MCDN does help handling of signalling between systems I did wonder if it might be needed

yes absorb digits is set to 0. When I have BCM Monitor running against the central system I see the incoming network call and then it seizes a line but the dialled digits from the remote end are sometimes missed when dialling on that external trunk. I currently only have an MCDN keycode on the...

I tried switching to SIP trunks between the two BCM 50's and the H is gone....

Yes I tried building a public route from the 'remote' BCM and have also tried removing the H323 config on both systems and switching to SIP trunking. Both changes result in the same- loss of digits when the remote BCM tries to dial out over the central BCMs trunks. Both systems are fully...

Yes you are right H shows that the call is a private network call. I read on the Meridian/CS1000 systems it's related to the term HLOC (home Location). I don't believe you could get it to appear on a single BCM as you'd need to get a call into it marked as a private network call, so would...

Probably bad form to followup my own post (sorry!) I did get this figured out - it seems that if I dial the access code for BCM A and then dial one of it's Line Pool access codes then the system does not impose the private network number length. However what I do find that unless I dial VERY...

In a network of say 2 BCM50's connected by H323 if the private DN length is 4 digits this works fine for set to set dialling between the systems. However if BCM B has no PSTN trunks and I want it to have access to the trunks on BCM A. I can setup a remote package etc. However how to I allow...

Hi In a network of BCM 50's (all on Rel 6 and patched) where H323 is used to network the systems together is there a way to suppress the H displayed on a destination sets display when a call is received? UDP is being used as the network type. I know on the larger CS1000's there was a plugin...