Search results for query: *

Any one successfully implemented IPC SIP with Cisco gear to provide internal hoot n holler services?

Sorry guys, I figured out what was wrong. The 25 pair from the cross-connect to the PBX was terminated incorrectly. Apparently, pin 2 is actually TN 5 on the PBX. This is a Nortel part as well!! I apologize for the confusion and thanks to everybody for your help!!

9201, I've tried the combination of ld 14 and 16 but was not successfuly in achieveing the intended result. Janaya, I have also tried Private line service and had the same result. Acewarlock, I'm trying to extend the copper line to the set. Both incoming and outbound dialing will be...

Is BARS/NARS required for do this? Any suggestions?

Thanks again Jamie2!

Thanks Jamie2, I'll look into this. I guess this set up won't work for our PRIs. Our receptionist is receiving tons of fax calls due to old DIDs we may have removed in the past.

I don't have call pilot. I have a M1 Option 11c with release 25.40. Is it possible with this system?

Is it possible to set up a DID so that voice calls go through but when a fax calls comes in it gets forwarded to another external fax line?

Did anyone get this working? I've tried changing the rcap and the net_data entries and still had no success.

Did anyone have any luck linking the 11c to an asterisk server? I am trying with no luck to connect the two using a PRI T1 card (with a CC card) on the Nortel side with a home made cable (as per instructed in http://www.tek-tips.com/viewthread.cfm?qid=888559) to the digium T1 Card on the...

Hello citytech, were you able to resolve this? I have ran into the same problem with not being able to set the clocking to internal.

Thanks guys!! I really appreciate your assistance. I tried setting this up but somehow it is still a no go. I'll try setting up a tie line using the existing pre-programmed ties in the system. I'll let you know if i'm successfuly. As a sanity check, would i be able to tie two systems using...

Hello Gene, Thanks again for helping me out with my T1 Traffic Study on my other thread. By the way, I changed FEDC to ETH and but I still don't hear a dialtone on my analog line on TN 9 0 0 0. I'm still trying to simulate a call from my digital phone on my digital line card with TN 2 0 0 0 to...

Hello John, I still have a slight problem. By trying to simulate your test, I have configured a phone on TN 2 0 0 0 with ext. 2220 and TN 2 0 0 1 with ext. 2221. I can call 2221 from 2220 and vice versa. I have a Univ Trunk Card on Slot 9 I configured route 20 similar to your route 37. I have...

Thanks John, I'll give it another shot. Can you also post the analog route and trunk? That way I may be able to see which parameter I may have inputted incorrectly or what I have missed. Thanks Again!!

I'm extremely confused in trying to connect 2 Nortel 11c using NT8D14 Universal Trunk Cards at each end in my lab. I tried building a route in ld 16 and then adding the trunks to the route I built in ld 14. I received SCH code after SCH codes to a point I no longer know if what I did was...

Thanks GHTROUT!! It worked successfully!!

Thanks!!! But sorry guys... I still don't have it up yet. The following was what I tried. sopc 0 2 NIL -- .sshc 0 20 2 24 2 20 02 24 02 -- 00 23 3 -- 1 2 3 4 5 6 7 -- .copc 0 2 2 -- .topc 0 2 NIL . TFC200 Based on this excel spreadsheet, I guess I should be looking for TFC002 for...

Thanks acewarlock. I am aware it is through LD 2. However it is not working for me. Think i am still doing something incorrectly. Would you be able to provide me a run down of the key steps I should take to atleast have it spit out a simple report? Please help!!! Thanks!!

Does anyone know how to capture the amount of traffic there is on the PRI with a given range of time? i.e. 9AM-5PM. I tried using the data bufferring and access feature but I couldn't capture anything. Not sure if I have configured it correctly. My goal is to determine if I can remove one of...