Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. endurevp

    External Call forward feature not working_11C

    Can you post the TN print out of your IT phone? Is CFXA set in the CLS?
  2. endurevp

    log

    PDT's RDTAIL is going to be your best bet as it does not get cleared during a restart.
  3. endurevp

    MC32S Unreg

    Did this get resolved? Is there and IP address conflict?
  4. endurevp

    Not CS1K question

    SSCs are a fussy bunch. Shut off the PBX, pull out the SSC, reseat the SSC, and turn the PBX back on. If that doesn't fix it and you swap SSCs don't forget to move the security "Coin" in the upper corner over to the new card.
  5. endurevp

    Moving loops from one Network Group to another.

    We did this not too long ago also. We moved SULP 4 to SUPL 40
  6. endurevp

    DID in IDC table to 500 set

    Can you please re-word you question? I'm no tunderstanding the problem.
  7. endurevp

    message lamp not lighting

    Use the XMWK key instead of MWK. You can specify what extension you want that message key to represent. MWK only indicate Primary DNs or a signle appearance non-PDN. XMWK MUST be a non-PDN.
  8. endurevp

    Meridian Option 11C - Fibre Expansion Cabinet Problem

    NTDK22 is a single port duaghterboard! You need a NTDK84 Dual port daughterboard in one of the SSC duaghterboard positions if you want 3 expansion cabinets.
  9. endurevp

    PRI CHANNELS IN MAKE BUSY

    Can you post you ADAN for the DCH, RDB and TNB of a trunk? Is there only one PRI or multiple? if mulitple are ther muliptle DCH? If so, are they Primary/Backup or individual configuration?
  10. endurevp

    HMS400 & NRP500 BAD LAMP errors

    Hi all, I work on a HMS400 and they have had NPR500 BAD LAMP errors for all of the 2nd lines of the analog room phones printing on their BGD printer since install. There are 2 extensions in each guest room (Line 1 and line 2 of a single 2 line phone) and each line is associated with the single...
  11. endurevp

    Nortel ACD Overflow DN with NRD status

    Try changing the MWC prompt to yes on the 4604 ACDN. It should allow you to use as an OVDN then.
  12. endurevp

    Power off Mermail Module without throwing a column light?

    I would like to power off the mermail module but don't want to throw a column light. We put in a server based mail. Mermail is the bottom module in a column so it will just sit there until I can convert it to an IPE module. Is there a way to turn the module OFF without throwing the column light?
  13. endurevp

    Ground start or Loop Start

    Good to know. Will keep it in mind. Thanks all.
  14. endurevp

    Ground start or Loop Start

    So I hear that you should always bring Ground start trunks into the PBX rather than Loop start as Loop start will have disconnect supervision problems. Anyone else heard this and have any insight. I have never had issues with Loop start trunks on any Nortel PBX I have worked on. Maybe I'm lucky.
  15. endurevp

    2000 series with 8 and 0 digits going bad

    I have recently been inundated with 2216 and 2616 sets where the digit 8 and some with the digit 0 just quit working. It is definitely the set as when a new one in put in it works fine. Is there and documentation showing that these sets have a tendency to go bad in that area of the dial pad? Has...
  16. endurevp

    HUNT when busy is not working properly.

    On the phones where you have multiple lines, try making all lines busy then place an additional call and see if it goes to voicemail correctly. In the Octel there is a feature in some mailboxes asking to check for matching mailboxes. Make sure that the check for matching mailbox is set to "no"...
  17. endurevp

    9150 vs MCK Extender 7000

    I have used the MCK 7000 and it is a good product. It interfaces with the meridian 1 via digital tn's with no need for the reach line card. That means the TN's will be located at your host site not at the remote site. It will allow for 24 digital phones and can be coupled with the MCK 6000 which...

Part and Inventory Search

Back
Top