Search results for query: *

Having problems with the system recognizing the 024-tdl. I have the latest processor. My rack has a 408 gs/id in slot 1, a 016 mlx in slot 2, a 016 etr in slot 3, and the 024-tdl is in slot 4. i read somewhere that it can be complicated to get the system to recognize the board. Anybody have...

ive tried swapping. still get the same outcome. I dunno if maybe when the processor was out someone changed the jumpers on the board without me knowing. Could that effect it? I have to 4.7's that seem to act the same. the rev 1 it came with seems to work fine with everything still but I...

after i do a board renumber in basin WinSPM, then do an inventory check using quick access, all i can see is the processor. I go through basic winSPM and add the boards. Then when i run the system inventory again, they show up but in surrogate mode.

okay. i have spent numerous hours trying to get this system to work. I have the processor, and 016-mlx an 024-tdl, and an 800ls/id installed. When i use the old magix rev 1, the system boots up and the system inventory shows everything in the rack. However, when i install the new r4.7, all...

Well we went from a old legend carrier to a new magix carrier. I have a r4.7 processor, an 024-TDL, 2-800 GS/LS-ID, and an 016 MLX Module. I read that the 024-tdl must be to the right of everything. Right now the old merlin legend is hooked up and running with a r3 processor. I am installing...

Well Dexman you were 100% correct. Our old processor was probably fine. However I noticed a few pins that were bent and when I went to bend them back, the ripped off the board. Good thing I bought the extra processor. Maybe when I have time I will solder them back on. It now finds the...

Just to give everyone a better picture. Right now i have 3 magix processors, 2-r4.7 and a r1.7. the rack i bought came with the r1.7, an 024 tdl, 2-800 gs/ls-id, and i added an 016 MLX since all the phones we have r mlx. Well i ordered 5 for the 024 tdl. If i use the processor that came with...

Okay i got the new rack and everything. With just the processor in, i get an error that says WinSPM cannot recognize the circuit pack in slot 1. Would removing the battery have done anything? I know have 3 processors and a new power rack. Still not getting anywhere

With the processor alone and the power supply I still have the same problem. I think it may be the rack. I am completely stumped. Trying not to spend unneeded funding. I even had problems trying to get the old merlin legend to boot back up. Seems like something may be loose but I cant see...

Got the new processor. Installed. And still having the same problem. I dunno if the old merlin legend rack is damaged or what. I am kind of stumped right now. I tried cleaning the contacts and still have no luck. any suggestions?

after it went to F I went and hooked up the cable for winspm. Saw I couldn't connect and went and checked it and there was nothing on the display, not even a red light. So I powered it down and then back up and that's when I got the red light. I tried 2 or 3 more times removing the batteries...

well I removed the batteries for about 10 minutes and reinstalled the processor. It booted back up and the green F came on. However, when I tried accessing it using winspm I couldn't connect. Then eventually the red error light came back on. Tried removing the batteries again and resetting...

Thanks for all your help. I have already ordered a new processor. However, I will still be checking to see if I can reset the old one back to default. I have everything backed up on a pc via winspm. Is there any reason why I would still need a PCMCIA backup card? I have one from the Merlin...

I have a Merlin Magix r4.7. It recently crapped out and needs to be replaced. Curious how to know if i buy one from someone, how i can tell what revision it is. Also, if it isnt the lastest revision, how can i go about upgrading it?

I just checked. as soon as i power the rack up the red light comes on on the processor. I cannot connect using winspm. Any other ideas before i order a new processor? Is there an internal battery that could have gone bad or that i could remove to erase any error codes? Also, i have no...

recently we lost power for about 2 hours. our generator never kicked on so the phone system was down for the full 2 hours. when the power returned, the processor, which is a merlin magix R4.7 would not boot back up and has a red light on it. i tried rebooting a few times but nothing. i...

i have the rack loaded with 016mlx but am only using two. When i get a chance i will remove everything i am not using and try again...

I have a Merlin Magix 4.0 V7.0. I purchased a a Merlin Messagin r2.0 off Ebay. After i installed it into the rack and powered up the rack, the system booted up for about 5 seconds and then shut down. The system will not boot up unless i remove the Merlin Messaging. Does this indicate the...

So far everything is working. One more question i have is when i page another extension the phone on the other end auto mutes. So if i page the office, they have to go to the phone and unmute it before they can talk back. Is there any way to se them so if u page another extension, the mute...

Thanks for that link. Very informative. I am looking for a programming manual or guide foe Merlin Magix 4.0 but cant find anything on avayas website. Can someone point me in the right direction.