Hey everyone. I have a merlin magix system 4.0 v7. i am trying to add a PagePal connected to an amplifier to page in our warehouse. I am unsure how or even where to start on hooking it up. I assume i need to run a line from the PagePal to the system, but unsure if it should go to an extension or a line. Also, i am unsure of where the switch on the PagePal should be set. I would like to be able to page to the pagepal and over the mlx phones simultaneously. I have the PagePal hooked to the amp and i know that is working by testing the chime feature. Also, i would need to know where to program the system to add the pagepal. any help would be greatly appreciated. thanks everyone.
Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
PagePal and Merlin Magix 4.0 v7.0
- Thread starter lvfrc183
- Start date
The first step for connecting a paging system to a Merlin Magix would be to obtain the documents for both pieces of equipment and getting familiar with everything.
With the Magix, you would option a port on an 800GS/LS-ID card as a page port, program paging buttons on the phone sets, connect the paging system to the Magix and enable the paging port in the Magix.
Obviously there are some intermediate steps, but this a rough list.
I![[love2]](/data/assets/smilies/love2.gif "[love2] [love2]")
"FEATURE 00"
With the Magix, you would option a port on an 800GS/LS-ID card as a page port, program paging buttons on the phone sets, connect the paging system to the Magix and enable the paging port in the Magix.
Obviously there are some intermediate steps, but this a rough list.
I
"FEATURE 00"Actually it could be any card with an unused gs/ls port.
To setup paging port on magix
system program,
AuxEquipp
Ldspkr Pg,
dial line/ trunk no (your unused line port for example 801)
enter
back
back
Then to add a page button to a phone
Before doing this, print or look in cntrl programming to see what buttons are already programmed, Sys access, and line assignments are the only thing that won't be over written by add lines(normal or paging) to a phone.
system program
Extensions
Lines/trunks
dial extension number you want to program
Enter
entry mode
dial line/trunk no (same as what you used above)
back
back
as for pagepal, try this
When Linux is Free and Open, who needs Windows or Gates?
To setup paging port on magix
system program,
AuxEquipp
Ldspkr Pg,
dial line/ trunk no (your unused line port for example 801)
enter
back
back
Then to add a page button to a phone
Before doing this, print or look in cntrl programming to see what buttons are already programmed, Sys access, and line assignments are the only thing that won't be over written by add lines(normal or paging) to a phone.
system program
Extensions
Lines/trunks
dial extension number you want to program
Enter
entry mode
dial line/trunk no (same as what you used above)
back
back
as for pagepal, try this
When Linux is Free and Open, who needs Windows or Gates?
- Thread starter
- #4
It's done this way:
Release 2.2 and later, assign telephones and loudspeaker page ports to Paging Groups:
Extensions→ or More→Group Page→Dial Paging Group no.(ENTER THE PAGING GROUP NUMBER)
→Enter→THE EXTENSION OR LINE NUMBER, Repeat as needed for additional Extensions. Back→Back
-merlinmansblog.blogspot.com
Release 2.2 and later, assign telephones and loudspeaker page ports to Paging Groups:
Extensions→ or More→Group Page→Dial Paging Group no.(ENTER THE PAGING GROUP NUMBER)
→Enter→THE EXTENSION OR LINE NUMBER, Repeat as needed for additional Extensions. Back→Back
-merlinmansblog.blogspot.com
- Thread starter
- #6
Well, I give that idea about 5 minutes of life. But I think it's time you went here:
-merlinmansblog.blogspot.com
-merlinmansblog.blogspot.com
- Thread starter
- #8
Avaya did not issue a programming guide per se for the R4 processor. The Feature Reference Guide for the R3 processor applies to the R4. A small guide was issued to cover the features new to the R4.
I "FEATURE 00"
I
"FEATURE 00"That would be:
There's not much difference between the R3 & R4, but this explains it.
-merlinmansblog.blogspot.com
There's not much difference between the R3 & R4, but this explains it.
-merlinmansblog.blogspot.com
- Thread starter
- #11
[COLOR=][/color]So far everything is working. One more question i have is when i page another extension the phone on the other end auto mutes. So if i page the office, they have to go to the phone and unmute it before they can talk back. Is there any way to se them so if u page another extension, the mute is off and they can talk back without hitting anything?
Paging from one phone to another.............
Just use HFAI at the receiving phone and that will work.
Actually, everyone who wants to do such automatic talk back should keep their HFAI Button on.
HFAI means Hands Free Answer Intercom.
-merlinmansblog.blogspot.com
Just use HFAI at the receiving phone and that will work.
Actually, everyone who wants to do such automatic talk back should keep their HFAI Button on.
HFAI means Hands Free Answer Intercom.
-merlinmansblog.blogspot.com
- Status
Similar threads
- Locked
- Question
- Locked
- Question
- Locked
- Question