Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations SkipVought on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. nollski

    New Install S8800's G450

    did you config the G450 for ip license-server???
  2. nollski

    CM 5.2.1 ESS WILL NOT REGISTER

    Does the cluster id and server id match ?
  3. nollski

    LSP/ESS won't register to Primary

    Check the reset-times transition-point on the gateways
  4. nollski

    PBX inserting # on International LD calling

    its on the trunk form screen, It is something that you can turn off.
  5. nollski

    Modular (RJ-45) to Amphenol adapter

    the adapter is a 356A and plug into #8
  6. nollski

    Modular (RJ-45) to Amphenol adapter

    259 has the wrong pin outs, sorry on the above but its the violet/orange and violet/green pairs on the amp which are pins 22/47 and 23/48. there was an old adapter that could of been used and am being told its a 356B but not sure.
  7. nollski

    Modular (RJ-45) to Amphenol adapter

    pins 1,2 and 4,5 on RJ45, and on the switch tail if wired to wall field already, yellow orange pr and yellow green pair. reversal might be needed. If not wired out to wall field and making your own amp then 22/47 23/48 also reversal might be needed. 1/2 to 22/47 or 4/5 to 22/47
  8. nollski

    LSP not saving trans

    Since it is not registered it will not get a save trans.One problem that I have seen is when you added the media gateway the wrong type of G250 was added. If its a G250 T1 then you have to add it as that type and not a generic G250.
  9. nollski

    AES SNMP Traps

    Trying to set up SNMP on AES.Is it able to send SNMP to say a S8730 or only to IBM Tivoli or HP Openview ??
  10. nollski

    G250-DS1 PRI signalling group drops

    Have you listed measurments to see if you are getting slips on that DS1
  11. nollski

    G250-DS1 PRI signalling group drops

    is the sync source set at the G250
  12. nollski

    Paging issue.

    Sounds like you have some type of backfeed going on. Have you tried disconnecting one of the bldgs and seeing if it cleared the problem???
  13. nollski

    S8500 LSP

    You didnt mention what software version you main svr is running.
  14. nollski

    Station not covering to voicemail.

    Sorry should of explained it better, is the terminate to coverage points with bridged appearances on the cover path set to yes
  15. nollski

    Station not covering to voicemail.

    Look at the coverage points on the cover path. Is it set to yes
  16. nollski

    Paging Ports

    That would depend on what type of paging system you have. If it doesn't require control leads then no.
  17. nollski

    S8300 MultiTech modem

    If this is an older modem and the S8300 is a newer software version it could be that the modem's firmware will need to be updated.
  18. nollski

    Avaya EMMC?

    Are you using G711 in the codec setting
  19. nollski

    Night Service to Voice Mail

    I just had this same problem and the fix was creating a VDN with the VDN in the listed directory night svc. The vector should point to night bell and also making it an attendant vector, but NOT ADDING the VDN number on the console paramaters attendant vector. By doing this it would then follow...
  20. nollski

    Call forward problem on v9

    Sounds like a Voip issue, do you have anymore info on the voip end??

Part and Inventory Search

Back
Top